ANALYSIS AND COMPARISON OF COMBINATIONAL CIRCUITS BY USING     161-174

International Journal of Advances in Engineering & Technology, March 2012. ©IJAET ISSN: 2231-1963 ANALYSIS AND COMPARISON OF COMBINATIONAL CIRCUITS BY USING LOW POWER TECHNIQUES Suparshya Babu Sukhavasi1, Susrutha Babu Sukhavasi1, Vijaya Bhaskar M2, B Rajesh Kumar3 1 Assistant Professor, Department of ECE, K L University, Guntur, AP, India. M.Tech -VLSI Student, Department of ECE, K L University, Guntur, AP, India. 3 M.Tech-Embedded VLSI Student, Department of ECE, SITE, T P Gudam, AP, India. 2 ABSTRACT Power dissipation is the major aspect which is effecting the digital circuits. By implementing the self resetting logic to the digital circuit, the power dissipation is drastically reduced. In the VLSI Design this low power technique is very advanced for DSP applications. The dynamic circuits are becoming increasingly popular because of the speed advantage over static CMOS logic circuits; hence they are widely used today in high performance and low power circuits. Self-resetting logic is a commonly used piece of circuitry that can be found in use with memory arrays as word line drivers. Self resetting logic implemented in dynamic logic families have been proposed as viable clock less alternatives. The combinational logic is a type of digital logic which is implemented by Boolean circuits, where the output is a pure function of the present input only. This is in contrast to sequential logic, in which the output depends not only on the present input but also on the history of the input. In this paper mainly the self resetting logic is applied for the different combinational circuits and the analysis is done very clearly. By implementing this low power technique for different logic circuits and adders, by comparison with DYNAMIC and SRCMOS logic’s power dissipation is drastically reduced up to 35% compared with CMOS logic circuits and observations are tabulated. KEYWORDS: High speed, VLSI, Self-resetting logic (SRL), topologies, power dissipation I. INTRODUCTION Combinational logic is used in computer circuits to do Boolean algebra on input signals and on stored data. Practical computer circuits normally contain a mixture of combinational and sequential logic. The part of an arithmetic logic unit, or ALU, that does mathematical calculations is constructed using combinational logic. Other circuits used in computers, such as half adders, full adders, half subtractors, full subtractors, multiplexers, demultiplexers, encoders and decoders are also made by using combinational logic. In today‘s fast processing environment, the use of dynamic circuits is becoming increasingly popular [5]. Dynamic CMOS circuits are defined as those circuits which have an additional clock signal inputs along with the default combinational circuit inputs of the static systems. Dynamic systems are faster and efficient than the static systems. A fundamental difficulty with dynamic circuits is the monotonicity requirement. In the design of dynamic logic circuits numerous difficulties may arise like charge sharing, feed through, charge leakage, single-event upsets, etc. In this paper novel energyefficient self-resetting primitive gates followed by the design of adder logic circuits are proposed. Addition is a fundamental arithmetic operation that is generally used in many VLSI systems, such as application-specific digital signal processing (DSP) architectures and microprocessors [2]. This module is the core of many arithmetic operations such as addition/subtraction, multiplication, division and address generation. Such high performance devices need low power and area efficient adder 161 Vol. 3, Issue 1, pp. 161-174 International Journal of Advances in Engineering & Technology, March 2012. ©IJAET ISSN: 2231-1963 circuits. So this paper presents a design construction for primitive gates and adder circuits which reduce delay and clock skew when compared to the dynamic logic adder implementation [9]. VDD Inputs Delay chain VSGR Nfet logic Cx Vx Cout Vout Fig.1. Basic Structure of A Self Resetting Logic Circuit Another category of dynamic circuits, called self-resetting CMOS (SRCMOS), represents signals as short-duration pulses rather than as voltage levels. When a set of pulses are sent to the inputs to a logic gate, they must arrive at essentially the same time and they must overlap with one another for a minimum duration. After a logic gate has processed a set of input pulses, a reset signal is activated that restores the logic gate to a state in which it can receive another set of input pulses. The reset operation is timed to occur after the input pulses have returned to zero [11]. Thus, there is no need for an evaluate or “foot” transistor since the pull-down network will be off during the reset operation, and this is one of the factors that leads to high-speed operation. Moreover, since the reset occurs immediately after each gate has evaluated, there is no need for a separate precharge phase. Since short-duration pulses are hard to debug and test, special additional test-mode features are sometimes added for these purposes. Two types of reset structures have been proposed for use in SRCMOS. In globally self-resetting CMOS [4], the reset signal for each stage is generated by a separate timing chain which provides a parallel worst-case delay path. Individual reset signals are obtained at various tap points along this timing chain in such a way that the reset pulse arrives at each stage only after the stage has completed its evaluation. Very careful device sizing based on extensive simulations over process-voltage-temperature corners are required in order to ensure correct operation. Moreover, any extra delay margin that is designed into the timing chain simply reduces the throughput by a corresponding amount. On the other hand, in locally self-resetting CMOS [5], the reset signal for each stage is generated by a mechanism local to that stage. Previous implementations of this technique have been based on single-rail domino stages in which the reset signal is obtained by sending the stage’s own output signal through a short delay chain. Again, this technique requires very careful simulations and device sizing in order to ensure that the reset signals do not arrive too early. As with the other technique, any timing margin that is built in will directly limit the achievable performance. II. SELF RESETTING CMOS DYNAMIC LOGIC Self-resetting logic is a commonly used piece of circuitry that automatically precharge they (i.e., reset themselves) after a prescribed delay. They find applications where a small percentage of gates switch in a cycle, such as memory decoder circuits. It is a form of logic in which the signal being propagated is buffered and used as the precharge or reset signal. By using a buffered form of the input, the input loading is kept almost as low as in normal dynamic logic while local generation of the reset assures that it is properly timed and only occurs when needed [6]. A generic view of a self-reset logic is shown in Fig.1. In the domino case, the clock is used to operate the circuit. In the self-resetting case, the output is fed back to the precharge control input and, after a specified time delay, the pull-up is reactivated. There is an NMOS sub block where the logic function performed by the gate is implemented which is represented as NMOS_LF through which the input 162 Vol. 3, Issue 1, pp. 161-174 International Journal of Advances in Engineering & Technology, March 2012. ©IJAET ISSN: 2231-1963 data‘s are loaded. The output of the gate F provides a pulse if the logic function becomes true. This output is buffered and it is connected to PMOS structure to precharge [7]. The delay line is implemented as a series of inverters. The signals that propagate through these circuits are pulses. VDD VSGR=VDD 0v Nfet logic Inputs Delay chain Cx Vx=0 VDD Cout Vout =0 Fig.2. Precharge Dynamic logic circuits are widely used in modern low power VLSI circuits. These dynamic circuits are becoming increasingly popular because of the speed advantage over static CMOS logic circuits; hence they are widely used today in high performance and low power circuits. Normally in the design of flip-flops and registers, the clock distribution grid and routing to dynamic gates presents a problem to CAD tools and introduces issues of delay and skew into the circuit design process [1]. There are situations that permit the use of circuits that can be automatically precharge themselves (i.e., reset themselves) after a prescribed delays [7]. These circuits are called post charge or self-resetting logic which are widely used in memory decoders. VDD Inputs VSGR= 0v Nfet logic VDD Delay chain Cx Vx=VDD 0v Cout Vout Fig.3. Discharge The width of the pulses must be controlled carefully or else there may be contention between NMOS and PMOS devices, or even worst, oscillations may occur. Self-resetting logic (SRL) can be classified as a variant of domino logic that allows for asynchronous operation [11]. A basic SRL circuit is shown in Figure. A careful inspection of the schematic shows that the primary differences between this gate and the standard domino circuit are 163 Vol. 3, Issue 1, pp. 161-174 International Journal of Advances in Engineering & Technology, March 2012. ©IJAET ISSN: 2231-1963 (a) The addition of the inverter chain that provides feedback from the output voltage Vout (t) to the gate of the reset pFET MR, and (b) The elimination of the evaluation nFET. Note that an odd number of inverters are used in the feedback. As discussed below, the feedback loop has a significant effect on both the internal operation of the circuit and the characteristics of the output voltage. Precharging of Cx occurs when the clock is at a value =0 and the circuit conditions are shown in Figure 2. During this time, and which is identical to the event in a standard domino circuit. As we will see, the timing of the input signals precludes the possibility of a DC discharge path to ground by insuring that the inputs to all logic nFET are 0 during precharge. The voltage on the gate of MR is at a value of so that insures that MR is in cutoff during this time. The distinct features of SRL arise when a discharge occurs. The circuit conditions are shown in Fig.3 III. ANALYSIS OF LOGIC GATES AND ADDERS This section presents the basic construction and simulation of primitive gates and adders in all the specified logics above they are DYNAMIC LOGIC, SRCMOS LOGIC, and SELF RESETTING LOGIC. The cells shown in Fig. is a self-resetting implementation of 2-input primitive gates. The logical functions are implemented by the NMOS stack with two input signals A and B. The delay path in this circuit is implemented with single inverter. The mechanism of self-resetting in this circuit is achieved through the PMOS transistors. The implementation of AND/OR can be obtained by placing the NMOS stack in series and parallel connection, whereas the gates NAND/NOR can be implemented with De Morgan‘s law, an OR gate with inverted input signals behaves as a NAND gate. Similarly an AND gate with inverted input signals behaves as a NOR gate [8]. 3.1 Dynamic logic implementation in logic gates and adders Dynamic logic is one of the low power technique which is applicable for digital circuits, in which the area will be reduced where as the power reduction is less compared to Self resetting logic. Analysis of basic logic gates and their applications is done. 3.1.1 And gate implementation Fig.4. schematic of and gate by using dynamic logic Fig.5. simulation results of and gate by using dynamic logic 164 Vol. 3, Issue 1, pp. 161-174 International Journal of Advances in Engineering & Technology, March 2012. ©IJAET ISSN: 2231-1963 3.1.2 Xor gate Fig.6. schematic of xor gate by using dynamic logic Fig.7. simulation results of xor gate by using dynamic logic 3.1.3 Half adder Fig.8. schematic of half adder by using dynamic logic Fig.9. simulation results of half adder by using dynamic logic 165 Vol. 3, Issue 1, pp. 161-174 International Journal of Advances in Engineering & Technology, March 2012. ©IJAET ISSN: 2231-1963 3.1.4 Full adder Fig.10. schematic of full adder by using dynamic logic Fig.11. simulation results of full adder by using dynamic logic 3.2 SRCMOS logic implementation in logic gates and adders Self resetting CMOS is one of the low power technique which is applicable for digital circuits, it yields high performance but having complexity circuitry, in which the area will be reduced where as the power reduction is less compared to Self resetting logic. Analysis of basic logic gates and their applications is done. 3.2.1 And gate Fig.12. schematic of and gate by using SRCMOS logic 166 Vol. 3, Issue 1, pp. 161-174 International Journal of Advances in Engineering & Technology, March 2012. ©IJAET ISSN: 2231-1963 Fig.13. simulation results of or gate by using SRCMOS logic 3.2.2 Xor gate Fig.14. schematic of xor gate by using SRCMOS logic Fig.15. simulation results of xor gate by using SRCMOS logic 167 Vol. 3, Issue 1, pp. 161-174 International Journal of Advances in Engineering & Technology, March 2012. ©IJAET ISSN: 2231-1963 3.2.3 Half adder Fig.16. schematic of half adder by using SRCMOS logic Fig.17. simulation results of half adder by using SRCMOS logic 3.2.4 Full adder Fig.18. schematic of full adder by using SRCMOS logic 168 Vol. 3, Issue 1, pp. 161-174 International Journal of Advances in Engineering & Technology, March 2012. ©IJAET ISSN: 2231-1963 Fig.19. simulation results of full adder by using SRCMOS logic 3.3 Self Resetting logic implementation in logic gates and adders Self resetting logic is a novel low power technique which is applicable for digital circuits, in which the power reduction is less compared to other mentioned low power techniques. Analysis of basic logic gates and their applications is done. 3.3.1 And gate Fig.20. schematic of and gate by using Self Resetting Logic Fig.21. simulation results of and gate by using self resetting logic 169 Vol. 3, Issue 1, pp. 161-174 International Journal of Advances in Engineering & Technology, March 2012. ©IJAET ISSN: 2231-1963 3.3.2 Xor gate Fig.22. schematic of xor gate by using Self Resetting Logic Fig.23. simulation results of xor gate by using self resetting logic 3.3.3 Half adder Fig.24. schematic of half adder by using Self Resetting Logic 170 Vol. 3, Issue 1, pp. 161-174 International Journal of Advances in Engineering & Technology, March 2012. ©IJAET ISSN: 2231-1963 Fig.25. simulation results of half adder by using self resetting logic 3.3.4 Full adder Fig.26. schematic of full adder by using Self Resetting Logic Fig.27. simulation results of full adder by using self resetting logic 171 Vol. 3, Issue 1, pp. 161-174 International Journal of Advances in Engineering & Technology, March 2012. ©IJAET ISSN: 2231-1963 IV. COMPARATIVE ANALYSIS OF COMBINATIONAL LOGIC CIRCUITS In half adder circuit the sum and carry is observed for this dynamic half adder the power dissipation is calculated and it is reduced up to 15% compared to CMOS logic. The total power dissipation for this circuit is 39.05 and in dynamic full adder circuit the power dissipation is calculated and it is reduced up to 15% compared to CMOS logic. The total power dissipation for this circuit is 56.90. Table 1 Power dissipation and delays of dynamic logic circuit Topology Rise delay ns(output node) 0.004 0.002 0.003 0.007 0.012 AND OR XOR HALF ADDER FULL ADDER Fall delay ns(output node) 0.002 0.001 0.002 0.005 0.01 Power Dissipation (mW) 26.45 26.45 47.89 39.05 56.90 In half adder circuit the sum and carry is observed for this SRCMOS half adder circuit the power dissipation is calculated and it is reduced up to 20% compared to CMOS logic[12]. The total power dissipation for this circuit is 35.19 and in this SRCMOS full adder circuit the power dissipation is calculated and it is reduced up to 20% compared to CMOS logic. The total power dissipation for this circuit is 50.21. Table 2 Power dissipation and delays of SRCMOS LOGIC Topology Rise delay ns(output node) 0.003 0.002 0.005 0.012 0.025 AND OR XOR HALF ADDER FULL ADDER Fall delay ns(output node) 0.005 0.005 0.004 0.033 0.014 Power Dissipation (mW) 24.21 24.21 43.35 35.19 50.21 In half adder circuit the sum and carry is observed for this SELF RESETTING LOGIC half adder circuit the power dissipation is calculated and it is reduced up to 35% compared to CMOS logic. The total power dissipation for this circuit is 30.17 and in this SELF RESETTING LOGIC full adder circuit the power dissipation is calculated and it is reduced up to 35% compared to CMOS logic. The total power dissipation for this circuit is 45.12 Table 3 Power dissipation and delays of SRL circuit Topology Rise delay ns(output node) 0.005 0.004 0.015 0.024 0.050 AND OR XOR HALF ADDER FULL ADDER V. Fall delay ns(output node) 0.001 0.001 0.002 0.022 0.043 Power Dissipation(mW) 23.12 23.12 36.67 30.17 45.12 ANALYSIS OF POWER DISSIPATION Table 4 Comparative Analysis of Power Dissipation Power dissipation DYNAMIC LOIC SRCMOS 172 AND OR 26.45 26.45 24.21 24.21 XOR 47.89 HALF ADDER 39.05 FULL ADDER 56.90 43.35 35.19 50.21 Vol. 3, Issue 1, pp. 161-174 International Journal of Advances in Engineering & Technology, March 2012. ©IJAET ISSN: 2231-1963 LOGIC SRL 23.12 23.12 36.67 30.17 45.12 Chart 1 analysis of power dissipation 60 50 40 30 DYNAMIC LOIC 20 SRCMOS LOGIC 10 SRL 0 AND IV. OR XOR HALF ADDER FULL ADDER CONCLUSION In this paper, an exhaustive analysis for commonly used high-speed primitive gates and adder circuits using self-resetting logic is implemented in 45-nm CMOS technologies. The goal was to obtain a family of gates that could simplify the implementation of fast processing circuit which overcomes the restriction due the pulses being elongated and shortened as signal traverse the logic stages. In this paper exhaustive comparison between conventional DYNAMIC LOGIC, SRCMOS and SRL were carried in terms of its parasitic value, delays and power dissipation. It is observed that the proposed circuits have offered an improved performance in power dissipation, charge leakage and clock skew when compared to DYNAMIC LOGIC and SRCMOS logic with additional burden of silicon area. Hence, it is concluded that the proposed designs will provide a platform for designing high performance and low power digital circuits and high noise immune digital circuits such as, digital signal processors and multiplexers. REFERENCES [1] Woo Jin Kim, Yong-Bin Kim, A Localized Self-Resetting Gate Design Methodology for Low Power IEEE 2001. [2] M. E. Litvin and S. Mourad, Self-reset logic for fast arithmetic applications, IEEE Transactions on Very Large Scale Integration Systems, vol. 13, no. 4, pp. 462–475, 2005. [3] L. Wentai, C. T. Gray, D. Fan, W. J. Farlow, T. A. Hughes, and R. K. Cavin, 250-MHz wave pipelined adder in 2- m CMOS, IEEE Journal of Solid-State Circuits, vol. 29, no. 9, pp. 1117–1128, 1994. [4] D. Patel, P. G. Parate, P. S. Patil, and S. Subbaraman, ASIC implementation of 1-bit full adder, in Proc. 1st Int. Conf. Emerging TrendsEng. Technol., Jul. 2008, pp. 463–467. [5] M. Lehman and N. Burla, Skip techniques for high-speed carry Propagation in binary arithmetic units, IRE Trans. Electron.comput., vol. EC-10, pp. 691–698, Dec. 1962. [6] R. A. Haring, M.S. Milshtein, T.I. Chappell, S. H. Dong and B.A. Chapell, "Self resseting logic and incrementer" in Proc. IEEE Int. Symp. VLSI Circuits, 1996 pp. 18-19. [7] G. Yee and C. Sechen, " Clock-delayed domino for adder and combinational logic design" in proc.IEEE/ACM Int. Conf. Computer Design, Oct., 1996, pp. 332-337. ! " #$$$ % lid-State Circuits, vol. 31, no. 6, pp. 841-846, June 1996. [9] P. Srivastava, A. Pua, and L. Welch, .Issues in the Design of Domino Logic Circuits, Proceedings of the IEEE Great Lakes Symposium on VLSI, pp. 108-112, February 1998. [10] W. Zhao and Y. Cao. New generation of predictive technology model for sub-45nm design exploration, In IEEE Intl. Symp. On Quality Electronics Design, 2006 [11] CMOS Logic Circuit Design 2002 John P Uyemura [12] Prabhakara C. Balla and Andreas Antoniou Low Power Dissipation MOS Ternary Logic Family IEE journal of solid state circuits, vol sc-19 no.5 October 1984 173 Vol. 3, Issue 1, pp. 161-174 International Journal of Advances in Engineering & Technology, March 2012. ©IJAET ISSN: 2231-1963 Authors Suparshya Babu Sukhavasi was born in A.P, India. He received the B.Tech degree from JNTU, A.P, and M.Tech degree from SRM University, Chennai, Tamil Nadu, India in 2008 and 2010 respectively. He worked as Assistant Professor in Electronics Engineering in Bapatla Engineering College for academic year 2010-2011 and from 2011 to till date working in K L University . His research interests include antennas, FPGA Implementation, Low Power Design and wireless communications. Susrutha Babu Sukhavasi was born in A.P, India. He received the B.Tech degree from JNTU, A.P, and M.Tech degree from SRM University, Chennai, Tamil Nadu, India in 2008 and 2010 respectively. He worked as Assistant Professor in Electronics Engineering in Bapatla Engineering College for academic year 2010-2011 and from 2011 to till date working in K L University . His research interests include antennas, FPGA Implementation, Low Power Design and wireless communications. Vijaya Bhaskar Madivada was born in A.P, India. He received the B.Tech degree in Electronics & Communications Engineering from Jawaharlal Nehru Technological University in 2010. Presently he is pursuing M.Tech VLSI Design in KL University; His research interests include FPGA Implementation, Low Power Design. B Rajesh Kumar was born in Gudivada, Krishna (Dist.,), AP, India. He received B.Tech. in Electronics & Communications Engineering from Jawaharlal Nehru Technological University in 2010 , A.P, India. Presently he is pursuing M.Tech. in VLSI from SITE. His research interest includes Low Power and design of VLSI circuits. 174 Vol. 3, Issue 1, pp. 161-174