Collimation system studies for the FCC-hh

Journal of Physics: Conference Series PAPER • OPEN ACCESS Collimation system studies for the FCC-hh To cite this article: R Bruce et al 2019 J. Phys.: Conf. Ser. 1350 012009 View the article online for updates and enhancements. This content was downloaded from IP address 198.252.56.98 on 16/12/2019 at 08:18 10th International Particle Accelerator Conference Journal of Physics: Conference Series 1350 (2019) 012009 IOP Publishing doi:10.1088/1742-6596/1350/1/012009 Collimation system studies for the FCC-hh R Bruce1 , A Abramov1,2 , A Bertarelli1 , M I Besana1 , F Carra1 , F Cerutti1 , A Faus-Golfe4 , M Fiascaris1 , G Gobbi1 , A Krainer1 , A Lechner1 , A Mereghetti1 , D Mirarchi1 , J Molson1 , M Pasquali1 , S Redaelli1 , D Schulte1 , M Serluca3 , E Skordis1 , M Varasteh1 1 European Organization for Nuclear Research (CERN), Geneva, Switzerland John Adams Institute at Royal Holloway University of London, Egham, United Kingdom 3 IN2P3-LAPP, Annecy-le-Vieux, France 4 LAL, Univ. Paris-Sud and Paris-Saclay, CNRS/IN2P3, Orsay, France 2 E-mail: [email protected] Abstract. The Future Circular Collider (FCC-hh) is being designed as a 100 km ring that should collide 50 TeV proton beams. At 8.3 GJ, its stored beam energy will be a factor 28 higher than what has been achieved in the Large Hadron Collider, which has the highest stored beam energy among the colliders built so far. This puts unprecedented demands on the control of beam losses and collimation, since even a tiny beam loss risks quenching superconducting magnets. We present in this article the design of the FCC-hh collimation system and study the beam cleaning through simulations of tracking, energy deposition, and thermo-mechanical response. We investigate the collimation performance for design beam loss scenarios and potential bottlenecks are highlighted. 1. Introduction The FCC-hh is a design study for a future 100 km long 50 TeV proton collider [1]. It features an unprecedented total stored beam energy of 8.3 GJ, a factor 28 higher than what has been achieved at the Large Hadron Collider (LHC) [2]. The uncontrolled loss of even a tiny fraction of the beam risks quenching a superconducting magnet or causing damage. It is therefore crucial that an ultra-efficient collimation system can intercept and absorb any beam losses. This article shows the conceptual design of the FCC-hh collimation system and its estimated performance in simulations. Previous studies of FCC-hh collimation are found in Refs. [3, 4, 5, 6]. The design goal for betatron losses in the FCC-hh is that a temporary beam lifetime (BLT) drop down to 0.2 h should be sustained over 10 s without a beam dump or quench. It is the same goal as set for the LHC [7] and the high-luminosity LHC (HL-LHC) [8]. It is pessimistic compared to LHC observations [9], which provides a safety margin. In the FCC-hh, it corresponds to an instantaneous beam loss power of 11.6 MW impacting on the collimation system. The collimation system must not only protect against unavoidable losses during regular operation but also protect from losses during failures [10, 11], help optimisation of the experimental backgrounds [12, 13], and provide satisfactory beam cleaning for ion operation, while keeping the impedance at acceptable levels, which is not treated in detail in this article. Content from this work may be used under the terms of the Creative Commons Attribution 3.0 licence. Any further distribution of this work must maintain attribution to the author(s) and the title of the work, journal citation and DOI. Published under licence by IOP Publishing Ltd 1 10th International Particle Accelerator Conference Journal of Physics: Conference Series 1350 (2019) 012009 IOP Publishing doi:10.1088/1742-6596/1350/1/012009 2. The FCC-hh collimation system The FCC-hh collimation system is based on the LHC system design [14, 15, 16, 10, 11], as well as foreseen upgrades for HL-LHC [8, 17, 18]. Similar collimators are assumed with two movable jaws and the beam in the middle. There are two dedicated collimation insertions: the 2.8 km long point J (PJ) for betatron cleaning and the 1.4 km long point F (PF) for momentum cleaning. The β-functions and the length have been scaled up by a factor 5 to achieve collimator gaps that are similar to the LHC both in mm and in beam σ. This ensures mechanical stability and acceptable impedance at σ-settings small enough to protect the aperture. The betatron system consists of a multi-stage hierarchy with robust primary collimators (TCP) at 7.6 σ, followed by secondary collimators (TCSG) at 8.8 σ, intercepting the secondary halo. Active tungsten absorbers (TCLA) at 12.6 σ form a third cleaning stage. Most TCSGs are made of Mo-graphite with a 5 µm Mo coating as in the HL-LHC [8] to ensure a tractable impedance [19]. The most loaded collimators (the first TCSG in PJ and the TCPs), are made of carbon-fibre-composite (CFC) with jaws that are thicker than for LHC collimators. In the TCP, protons may suffer a significant energy loss in single-diffractive scattering, but only a small betatron kick. Such protons risk to bypass downstream collimators in the straight section and be lost in the dispersion suppressor (DS) where the dispersion rises. Special collimators (TCLD) are therefore installed in the DS to intercept these losses, as in the HLLHC [17, 18]. TCLDs are also installed in the insertions for experiments and extraction. In addition, tertiary tungsten collimators (TCTs) at 10.5 σ are installed upstream of the experiments to protect the final-focus triplets. 3. Cleaning performance Figure 1. The simulated cleaning inefficiency for a 50 TeV horizontal betatron halo with collision optics (β ∗ =30 cm). Tracking simulations are used to estimate the loss pattern around the ring using the coupling [20, 21, 22] between SixTrack [23, 24, 16, 25] and FLUKA [26, 27]. SixTrack tracks protons through the magnetic lattice and FLUKA simulates the proton-matter interactions in collimators. Protons are tracked until they hit the machine aperture or undergo a nuclear inelastic reaction in a collimator. This framework has shown good agreement with measurements of LHC beam losses [28]. The starting beam distribution is a halo with a large enough amplitude to hit the TCPs on the first turn as described in Ref. [16], at a very shallow 0.2 nm impact depth. In these studies, 108 protons are tracked for 200 turns. Figure 1 shows the simulated pattern of horizontal betatron losses around the FCC ring for the , most critical case of 50 TeV, expressed in terms of the local cleaning inefficiency ηc (s) = EE(s) tot ∆s where ∆s is the longitudinal bin size of 10 cm, E is the energy that impacts the physical aperture in a given bin, and Etot is the total energy deposited in the full simulation (including collimator 2 10th International Particle Accelerator Conference Journal of Physics: Conference Series 1350 (2019) 012009 IOP Publishing doi:10.1088/1742-6596/1350/1/012009 jaws). The main losses occur, as expected, on the collimators in PJ (s ≈73 km). The TCLDs protect very efficiently the DS and only a very small fraction of protons leaks out of PJ. The required ηc to avoid quenches is estimated at ηc,max = 3 × 10−7 /m at 50 TeV, assuming a 0.2 h BLT, and that losses of 4.3 × 105 p/m/s cause a 10 mW/cm3 peak power [29], which is the assumed quench limit. Figure 1 shows that the collimation system successfully keeps the cold losses well below ηc,max all over the ring, in spite of the very challenging loss conditions. Studies with collimator imperfections as in Ref. [16] show that local losses could increase on average by a factor 2, bringing the average close to, but not above, the quench limit. Similar simulations have been performed also for vertical losses, for the cleaning at injection, for off-momentum cleaning, and for accidental impacts during asynchronous beam dumps, and no showstoppers were found. It should be noted though that, opposite to the LHC, there is no skew TCP in the FCC-hh, since it would receive unsustainable power loads if installed right downstream of the horizontal and vertical TCPs. The losses to cold magnets are still acceptable for a skew halo, however, primary losses would occur at the TCSGs, which might cause too high loads for a 0.2 h BLT. The limit remains to be quantified through thermo-mechanical studies, but the acceptable loss rate is lower in the skew plane than in the horizontal and vertical ones. In the LHC, no large skew losses have been observed, and if the FCC-hh behaves similarly, the lower tolerance in the skew plane is not a showstopper. 4. Energy deposition studies The tracking simulations show that the primary proton losses are acceptable. However, for a detailed quench assessment, local energy deposition studies, including the shower development, are needed for the most loaded magnets. A FLUKA geometry was implemented, with the TCLD in cell 8 and two downstream magnets (a quadrupole and a dipole), which are expected to be most critical [30]. Magnetic fields were included, modelled as perfect quadrupolar or dipolar fields. Several layouts of TCLDs and fixed masks were tested. The collimators were modelled as two parallel blocks and the masks as cylinders made of tungsten. In total 4.57 × 106 50 TeV protons impacting the TCLD were simulated, with starting conditions from beam tracking, and the shower was tracked in FLUKA. The results, normalised to a power load for a 0.2 h BLT, show that the loads stay below 5 mW/cm3 in all superconducting coils for a 1.0 m TCLD followed by a second 1.5 m TCLD, and a 0.5 m mask in front of the quadrupole, and an additional 1.5 m TCLD and a 0.15 m mask in front of the dipole. This number, a factor 2 below the assumed quench limit, includes already a factor 8 safety margin to account for the effects of both imperfections and the discrepancy between measurements and simulations found in LHC studies [16]. It is thus concluded that the baseline layout successfully protects the most exposed magnets. The power deposition is a severe challenge also for the robustness of the collimators and other elements in the warm section. Therefore, the full 2.7 km PJ was modelled in FLUKA, including collimators, warm magnets and passive absorbers. Impacts of protons hitting collimators, from the tracking, were used as initial conditions to simulate the showers. The case of vertical beam losses with a 0.2 h BLT was considered as the most critical case, since there is more space for the shower development to the critical downstream elements for impacts on the most upstream TCP. Initial iterations showed the need to increase the thickness of the TCPs and the first TCSG, to shorten the TCPs to 30 cm, and to remove the skew TCP that would otherwise receive an unsustainable 260 kW power deposition. The results show that almost half of the power is taken by the tunnel walls, while a significant fraction is absorbed by the beam pipes along 2.7 km. The first TCSG is the collimator with the highest total power (92 kW), as shown in Fig. 2. Despite an integral load 14 times lower, the directly-impacted TCP is exposed to the highest power density, due to the multi-turn ionisation by primary protons. The power density peaks at 50 kW/cm3 on the surface, but 100 µm inside 3 10th International Particle Accelerator Conference Journal of Physics: Conference Series 1350 (2019) 012009 IOP Publishing doi:10.1088/1742-6596/1350/1/012009 Figure 2. The simulated power density on the most loaded TCSG for a 0.2 h BLT. it is one order of magnitude smaller. Two 17 m long warm dipoles, which are used to create a chicane in the insertion, are particularly impacted as they are exposed to the TCP showers. At the front face, the second module reaches 270 kW/m, while the absorbed power is at about 60 kW/m over the rest of its length. The high loads at the face could be mitigated by an appropriate cooled shielding. As future work, the cooling of the rest of the magnet should be studied carefully, keeping in mind that these loads need to be sustained over 10 s. 5. Collimator robustness studies Preliminary finite element analyses have been conducted with Ansys v18.2 to assess the risk for collimator damage, using as input the energy deposition from FLUKA. The first TCSG, with the highest total load, as well as the vertical TCP, with the highest peak power density, were both studied. A thermal analysis was performed first, which was later coupled to a static structural analysis to obtain the mechanical response of the system, as in Ref. [31]. A pessimistic steady-state condition with a 1 h BLT was assumed at the start, from which the losses were increased during 10 ms to a 0.2 h BLT, which was kept for 10 s. The losses were then ramped down to a 1 h BLT again. Some simplifying assumptions were made: a perfect bonding between the CFC absorbers and the Glidcop housing is assumed, as well as a linear constitutive law between stress and strain for the absorbers and a constant temperature profile for the water flowing inside the cooling circuit. The model of an LHC TCSP collimator was used as a starting point for the study, and minor modifications were performed to reflect the FCC-hh design updates. The study for 1 h BLT did not show worrying results and we focus in the following on 0.2 h BLT. A 330◦ C peak temperature is found on the TCSG jaw. This induces thermal deformations, strains, and stresses on the different components, due to the temperature gradient and the thermal-expansion coefficient mismatch between the materials. No permanent damage occurs on the jaw, although temporary deflections of up to 375 µm are observed (see Fig. 3). The only permanent deformations occurred on the cooling pipes. This issue is not a showstopper, as it can be mitigated by adopting a higher yield-strength material. The peak temperature on the TCP jaw is about 660 ◦ C. This causes a maximum stress of 45 MPa and a strain of about 8000 µm/m in the absorber-housing contact region, theoretically leading to failure. However, similar temperatures have already been achieved repeatedly on 4 10th International Particle Accelerator Conference Journal of Physics: Conference Series 1350 (2019) 012009 IOP Publishing doi:10.1088/1742-6596/1350/1/012009 Figure 3. Deflections of the TCSG jaw for a 0.2 h BLT. CFC absorbers during past experiments, without any sign of failure, and with thermal gradients largely exceeding those at hand in the present study [32, 33]. The high values of stress and strain are therefore thought to be due to the assumed simplified absorber-housing contact, as well as to the hypothesis of linear elasticity considered for CFC. Both these assumptions cause a stiffer structure than the real case. For the same reason, the obtained beam-induced deflection of 155 µm is believed to underestimate the real deformation of the jaw. Future studies should include refined assumptions. No permanent damage is found on other parts of the TCP structure. Another potential concern is that the out-gassing from CFC risks to be very high at the simulated temperatures. The resulting beam vacuum and the possible need for dedicated pumping should be evaluated in future studies. 6. Conclusions With a total stored energy of 8.3 GJ, the FCC-hh poses severe challenges for the protection against beam losses. We have shown a conceptual design of the FCC-hh collimation system, based on the LHC and HL-LHC but with several modifications and additions. Simulations show that the proposed design can efficiently protect the superconducting magnets from quenches even during a beam lifetime drop to 0.2 h at 50 TeV, corresponding to 11.6 MW loss power. The presented collimation design has thus demonstrated a satisfactory performance in spite of extremely challenging design requirements. Thermo-mechanical analyses of the most loaded collimators highlighted some issues which, without representing any serious showstopper at this stage, will need to be followed up in future design developments. Points that need to be addressed include the material choice for the cooling pipes, an improved simulation model for the bonding between the absorber and the housing, the out-gassing from collimators due to high instantaneous temperatures, as well as the local shielding and cooling of the warm dipoles. Acknowledgments The European Circular Energy-Frontier Collider (EuroCirCol) project has received funding from the European Union’s Horizon 2020 research and innovation programme under grant No 654305. the information herein only reflects the views of its authors and the European Commission is not responsible for any use that may be made of the information. 5 10th International Particle Accelerator Conference Journal of Physics: Conference Series 1350 (2019) 012009 IOP Publishing doi:10.1088/1742-6596/1350/1/012009 References [1] M [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] [17] [18] [19] [20] [21] [22] Benedikt et al 2018 Future Circular Collider CERN-ACC-2018-0058 URL https://cds.cern.ch/record/2651300 Brüning O S, Collier P, Lebrun P, Myers S, Ostojic R, Poole J and P Proudlock (editors) 2004 LHC design report v.1 : The LHC main ring CERN-2004-003-V1 Fiascaris M, Bruce R, Mirarchi D and Redaelli S 2016 First Design of a Proton Collimation System for 50 TeV FCC-hh Proceedings of the International Particle Accelerator Conference 2016, Busan, Korea 2425 URL http://accelconf.web.cern.ch/AccelConf/ipac2016/papers/wepmw006.pdf Fiascaris M, Bruce R and Redaelli S 2018 A conceptual solution for a beam halo collimation system for the future circular hadron-hadron collider (fcc-hh) Nucl. Instrum. Methods Phys. Res. A 894 96 – 106 ISSN 0168-9002 URL http://www.sciencedirect.com/science/article/pii/S0168900218303759 Molson J, Faus-Golfe A, Bruce R, Fiascaris M, Krainer A and Redaelli S 2017 Status of the FCC-hh collimation system Proceedings of the International Particle Accelerator Conference 2017, Copenhagen, Denmark 64 URL http://accelconf.web.cern.ch/AccelConf/ipac2017/papers/mopab001.pdf Besana M I et al. 2017 Energy deposition in the betatron collimation insertion of the 100 TeV future circular collider Proceedings of the International Particle Accelerator Conference 2017, Copenhagen, Denmark 68 URL http://accelconf.web.cern.ch/AccelConf/ipac2017/papers/mopab003.pdf Assmann R W 2002 Preliminary Beam-based specifications for the LHC collimators Tech. Rep. LHCPROJECT-NOTE-277 CERN Geneva URL http://cds.cern.ch/record/691766 Apollinari G, Alonso I B, Bruning O, Fessia P, Lamont M, Rossi L and L Tavian (editors) 2017 HighLuminosity Large Hadron Collider (HL-LHC): Technical Design Report V. 0.1 CERN Yellow Reports: Monographs. CERN-2017-007-M (Geneva: CERN) URL https://cds.cern.ch/record/2284929 B Salvachua et al 2019 Overview of Proton Runs During Run 2 Proceedings of the 9th LHC Operations Evian Workshop, Evian, France URL https://indico.cern.ch/event/751857/timetable Bruce R, Assmann R W and Redaelli S 2015 Calculations of safe collimator settings and β ∗ at the CERN Large Hadron Collider Phys. Rev. ST Accel. Beams 18(6) 061001 URL http://link.aps.org/doi/10.1103/PhysRevSTAB.18.061001 Bruce R, Bracco C, Maria R D, Giovannozzi M, Mereghetti A, Mirarchi D, Redaelli S, Quaranta E and Salvachua B 2017 Reaching record-low β ∗ at the CERN Large Hadron Collider using a novel scheme of collimator settings and optics Nucl. Instrum. Methods Phys. Res. A 848 19 – 30 URL http://www.sciencedirect.com/science/article/pii/S0168900216313092 Bruce R et al. 2013 Sources of machine-induced background in the ATLAS and CMS detectors at the CERN Large Hadron Collider Nucl. Instrum. Methods Phys. Res. A 729 825 – 840 Bruce R et al. 2019 Collimation-induced experimental background studies at the CERN Large Hadron Collider Phys. Rev. Accel. Beams 22(2) 021004 URL https://link.aps.org/doi/10.1103/PhysRevAccelBeams.22.021004 RW Assmann 2005 Collimators and Beam Absorbers for Cleaning and Machine Protection Proceedings of the LHC Project Workshop - Chamonix XIV, Chamonix, France 261 RW Assmann et al 2006 The Final Collimation System for the LHC Proc. of the European Particle Accelerator Conference 2006, Edinburgh, Scotland 986 Bruce R et al. 2014 Simulations and measurements of beam loss patterns at the CERN Large Hadron Collider Phys. Rev. ST Accel. Beams 17(8) 081004 URL http://link.aps.org/doi/10.1103/PhysRevSTAB.17.081004 Bruce R, Marsili A and Redaelli S 2014 Cleaning Performance with 11T Dipoles and Local Dispersion Suppressor Collimation at the LHC Proceedings of the International Particle Accelerator Conference 2014, Dresden, Germany 170 URL http://accelconf.web.cern.ch/AccelConf/IPAC2014/papers/mopro042.pdf Lechner A et al. 2014 Power Deposition in LHC Magnets With and Without Dispersion Suppressor Collimators Downstream of the Betatron Cleaning Insertion Proceedings of the International Particle Accelerator Conference 2014, Dresden, Germany 112 URL http://accelconf.web.cern.ch/AccelConf/IPAC2014/papers/mopro021.pdf Arsenyev S, Boine-Frankenheim O and Schulte D 2018 FCC-hh transverse impedance budget Proceedings, 9th International Particle Accelerator Conference (IPAC 2018): Vancouver, BC Canada, April 29-May 4, 2018 MOPMF029 A Mereghetti et al 2013 Sixtrack-FLUKA active coupling for the upgrade of the SPS scrapers Proceedings of the International Particle Accelerator Conference 2013, Shanghai, China 2657 Mereghetti A 2015 Performance Evaluation of the SPS Scraping System in View of the High Luminosity LHC Ph.D. thesis University of Manchester Skordis E, Vlachoudis V, Bruce R, Cerutti F, Ferrari A, Lechner A, Mereghetti A, Ortega P, 6 10th International Particle Accelerator Conference Journal of Physics: Conference Series 1350 (2019) 012009 [23] [24] [25] [26] [27] [28] [29] [30] [31] [32] [33] IOP Publishing doi:10.1088/1742-6596/1350/1/012009 Redaelli S and Pastor D S 2018 FLUKA coupling to Sixtrack CERN-2018-011-CP, Proceedings of the ICFA Mini-Workshop on Tracking for Collimation, CERN, Geneva, Switzerland 17 URL https://cds.cern.ch/record/2646800?ln=en Schmidt F 1994 SixTrack. User’s Reference Manual CERN/SL/94-56-AP Robert-Demolaize G, Assmann R, Redaelli S and Schmidt F 2005 A new version of sixtrack with collimation and aperture interface Proc. of the Particle Accelerator Conf. 2005, Knoxville 4084 Sixtrack web site http://sixtrack.web.cern.ch/SixTrack/ Ferrari A, Sala P, Fassò A and Ranft J 2005 FLUKA: a multi-particle transport code CERN Report CERN2005-10 Battistoni G et al. 2015 Overview of the fluka code Annals Nucl. Energy 82 10–18 Auchmann B et al. 2015 Testing beam-induced quench levels of LHC superconducting magnets Phys. Rev. ST Accel. Beams 18(6) 061002 Varasteh M et al. 2018 Cold loss studies for the quench limit assessment Presentation at the 4th EuroCirCol Meeting URL https://indico.cern.ch/event/733292/contributions/3147557 Krainer A 2019 Design & Simulation of new protection devices in the dispersion suppressor regions for the Future Circular Collider Project Master’s thesis Graz University of Technology, in press Austria Dallocchio A 2008 Study of thermomechanical effects induced in solids by high-energy particle beams: analytical and numerical methods Ph.D. thesis Turin Polytechnic URL http://cds.cern.ch/record/1314219 Carra F 2017 Thermomechanical response of advanced materials under quasiinstantaneous heating Ph.D. thesis Turin Polytechnic URL https://doi.org/10.5281/zenodo.1240449 Bertarelli A et al. 2018 Dynamic testing and characterization of advanced materials in a new experiment at CERN HiRadMat facility Journal of Physics: Conference Series 1067 082021 7