Recent Advancements in GaN LED Technology

We are IntechOpen, the world’s leading publisher of Open Access books Built by scientists, for scientists 6,700 181,000 195M Open access books available International authors and editors Downloads Our authors are among the 154 TOP 1% 12.2% Countries delivered to most cited scientists Contributors from top 500 universities Selection of our books indexed in the Book Citation Index in Web of Science™ Core Collection (BKCI) Interested in publishing with us? Contact [email protected] Numbers displayed above are based on latest data collected. For more information visit www.intechopen.com Chapter Recent Advancements in GaN LED Technology Thamer A. Tabbakh, Deepak Anandan, Michael J. Sheldon, Prashant Tyagi and Ahmad Alfaifi Abstract Gallium nitride (GaN)-based solid state lighting technology has revolutionized the semiconductor industry. The GaN technology has played a crucial role in reducing world energy demand as well as reducing the carbon footprint. As per the reports, the global demand for lighting has reduced around 13% of total energy consumption in 2018. The Department of Energy (USA) has estimated that bright white LED source could reduce their energy consumption for lighting by 29% by 2025. Most of the GaN LEDs are grown in c-direction, and this direction gives high growth rate and good crystal integrity. On the other hand, the c-plane growth induces piezoelectric polarization, which reduces the overall efficiency of LEDs since the last decade researchers round the globe working on III-N material to improve the existing technology and to push the limit of III-V domain. Now, the non-polar and semi-polar grown LEDs are under investigation for improved efficiency. With the recent development, the GaN is not only limited to lighting, but latest innovations also led the development of microLEDs, lasers projection and point source. These developments have pushed GaN into the realm of display technology. The miniaturization of the GaN-based micro-LED and integration of GaN on silicon driving the application into fast response photonic integrated circuits (ICs). Most of the recent advancements in GaN LED field would be discussed in detail. Keywords: GaN, polar, non-polar, polarization, GaNLEDs, GaN micro LEDs 1. Introduction Group III-nitrides (GaN, AlN, and InN) and their alloys have been considered the most promising semiconductor materials for various optoelectronic applications due to their excellent physical properties and stability in harsh environmental conditions [1–3]. Today, III-nitrides-based light-emitting diodes (LEDs) are widely used for solid-state lighting (SSL) applications all over the world because of their high efficiency, low power consumption, and longer lifetime than fluorescent and incandescent bulbs [4, 5]. Specifically, white light LEDs are a more promising low-power light resource to replace conventional fluorescent, as shown in Figure 1. Along with LEDs, III-nitride-based laser diodes (LDs), high-power electronics, photodetectors, etc., are other extended optoelectronic applications that are also demonstrated [7, 8]. However, 1 Light-Emitting Diodes - New Perspectives Figure 1. (a) Structure of white LED, (b) YAG-ce phosphor used to generate white LED by blue emission; and (c) emission spectra of first white LED (covers blue – Yellow- red) [4], where the typical distance between +ve and -ve lead wire is 0.3 mm for 5 mm LED [6]. developing III-nitride-based devices is not straightforward due to various difficulties and challenges. Among these, the preparation of high-quality and large-area singlecrystalline bulk III-nitride semiconductors which has been one of the significant challenges over the last few decades because of the poor solubility of nitrogen gas in IIImetals (In, Ga and Al) [9–11]. For example, GaN single crystal growth requires a high growth temperature (2220°C) and high growth pressure (6 GPa) [9]. The bulk singlecrystal GaN growth cannot be employed in the standard Czochralski or Bridgman techniques, generally used to prepare bulk Si and GaAs substrates [11]. However, to take advantage of III-nitrides material physical properties and their chemical stability, III-nitrides material is hetero-epitaxially grown on various substrates [1, 3]. In semiconductor epitaxy, the most favorable approach is homoepitaxy in which same substrate is used for the growth of targeted semiconductor material. But this approach is not possible for III-nitride based material due to the unavailability of bulk GaN substrates. Hence, hetroepitaxy route is chosen for the growth of GaN based material. Hetroepitaxy means growth of material on foreign substrate. For example, most of the GaN devices are grown on sapphire which is highly lattice mismatched with GaN. Due to heteroepitaxial growth process the grown epilayers suffer from high level of in-plane strain and structural defects like dislocation, stacking faults, etc. Generally, nitridation of sapphire is performed before GaN growth as pre-nitridation step. This pre-nitridation helps in formation of an intermediate AlN layer which compensate for plane strain to some extent [12–15]. Because of the said reason, large area singe- crystalline bulk III-nitride semiconductor fabrication is challenging. Over the last few decades, research has been done to improve the structural, optical, and electronic properties of GaN devices. 2 Recent Advancements in GaN LED Technology DOI: http://dx.doi.org/10.5772/intechopen.107365 1.1 Breakthrough: P-type doping Today, scientific advancement brings tremendous progress in improving the crystalline quality of III-nitrides semiconductors, which enable the development of highly efficient and durable III-nitride-based optoelectronic devices for commercial applications [4, 5, 7, 8]. The GaN material was first time discovered by Johnson et al. in the year of 1932. This work obtained polycrystalline GaN by passing ammonia (NH3) gas over hot gallium metal at 900–1000°C temperature conditions [16]. However, the epitaxial growth of GaN film on sapphire (0001) was presented in 1969s by Maruska and Tietjen using the hydride vapor phase epitaxy (HVPE) growth technique [17]. Thereafter, Manasevit et al. reported the growth of epitaxial GaN film on a sapphire substrate using metalorganic vapor phase epitaxy (MOVPE) [18]. However, these hetero-epitaxial grown GaN films on sapphire substrates have poor crystal quality and high-density n-type carriers (>1018 cm−3), which makes it challenging to achieve p-type doping into the GaN films [19, 20]. Yoshida et al. addressed that the molecular beam epitaxy (MBE) growth of GaN film on AlN-coated sapphire has shown better electrical and optical properties than the directly grown GaN on the sapphire substrate [21]. Amano et al. reported that the thin AlN buffer layer on the sapphire substrate improves the epitaxial GaN film crystalline quality [22]. Nakamura et al. also noted the growth of enhanced crystalline quality GaN on the low-temperature GaN buffer layer on the sapphire substrate before the primary GaN film growth [23]. The major development of III-nitride optoelectronic devices was initiated by Amano et al. after successfully p-type (Mg-acceptor) doping into the GaN film by using a low-energy electron beam irradiation method, which has opened a way to develop the p-n junction-based LEDs [24]. However, it was noticed that the Mg acceptor doped GaN film has a high electrical resistivity due to the formation of acceptor-H complexes [3, 20]. Nakamura et al. have shown that the p-GaN film hole carrier activation was achieved by a simple thermal annealing process in the N2 gas environment [25]. The high temperature thermally annealed p-GaN film has shown a high hole carrier concentration of ~3 × 1017 cm−3 with mobility of 10 cm2/Vs and low contact electrical resistivity of 2 Ω.cm as shown in Figure 2 [25]. Furthermore, the growth of high crystalline InGaN film on GaN film by using metalorganic chemical vapor deposition (MOCVD) has a strong band-edge emission peak at room temperature photoluminescence (PL), which is another breakthrough for developing LEDs devices [27]. In 1993, Nakamura et al. successfully reported the first GaN-based blue LED with a light output power of 125 μW and external quantum efficiency (EQE) of 0.22% [26]. Later, the significant development progress in III-nitride semiconductor research enabled highly efficient SSL LED devices (Figure 3). 1.2 III-N alloy for wide spectral emission III-N-based materials are the leading contender to fill the wavelength from 500 to 600 nm. Alloys of AlGaInN/GaN cover a broad spectrum of deep ultraviolet to near-infrared (AlN-6.2 eV, GaN-3.4 eV, and InN-0.65 eV) by easing the severe bottleneck of low-output efficiency by other semiconductor emitters such as ZnSe as shown in Figure 1. Around the 1990s, Nakamura et al. successfully developed high-quality GaN epifilm and made efficient p-type GaN film using high-temperature annealing to realize high-efficiency blue-light LED. Taking advantage of the momentum, researchers 3 Light-Emitting Diodes - New Perspectives Figure 2. Resistivity of Mg-doped GaN films for different annealing temperatures. (b) Output power comparison between commercially available SiC LEDs and p-n junction GaN LEDs [26]. Figure 3. The SSL LEDs efficiency improvement at laboratory demonstration and comparison with incandescent and fluorescent bulb efficiencies [4]. push blue GaN LEDs EQE to exceed 80%, while emissions wavelengths move to the red spectra range. In 1996, Nakamura et al. demonstrated the first short wavelength (417 nm) GaN LD. Since then, the 405 nm violet InGaN laser source has been commercially successful for high-definition video and multi-layer data storage. Using GaN-based blue LDs increases the data storage capabilities per disc in the blue-ray systems [28]. For their significant contribution in developing III-nitride-based LEDs, Shuji Nakamura, Hiroshi Amano, and Isamu Akasaki received the prestigious Noble Prize in physics in 2014 [29]. Today, the III-nitride-based LEDs have been proven to be highly efficient, have a long lifetime, and are environment friendly [4, 30]. The III-nitride-based white LEDs 4 Recent Advancements in GaN LED Technology DOI: http://dx.doi.org/10.5772/intechopen.107365 have high efficiency of 200 lm/W, and are commercially available for light applications [4]. The III-nitride semiconductors-based LEDs are used in almost every traffic signal, medical application, cell phone display, monitor, house/street, car, and so on [2, 30, 31]. Haitz et al. addressed that SSL LED lighting decreases electrical power consumption by more than 50% and is directly related to reducing CO2 gas emissions by approximately 200 Megatons per year [32]. 2. Polar-InGaN/GaN for blue and green LEDs Acceleration of blue and green LEDs development from InGaN/GaN quantum well (QW) started after the successful invention of p-type GaN by low-energy electron irradiation in late 1989 by Amano et al. [24]. This invention led to high quantum efficiency and output power. However, InGaN/GaN growth along c-plane sapphire [0001] induces a polarization effect which causes quantum confined Stark effect (QCSE) and carrier loss (droop effect). The QCSE reduces the probability of radiation recombination by separating the hole and electron wave function on the QW. Especially, QCSE and polarization effects are highly pronounced with high indium (In) content incorporation in the InGaN epilayer [29]. The InGaN has the advantage of covering a wide spectral range from blue, green, and ultraviolet by tuning energy from 0.7 to 3.4 eV. Theoretically, when the indium composition is between 15 and 20% and 25–30%, the emission wavelengths belong to blue and green LEDs, respectively. However, to cover ultraviolet emission, the indium mole fractions should increase to a large extent, increasing threading dislocation density in the active layer. High threading dislocation density reduces internal quantum efficiency; therefore, InGaN material is not suitable for ultraviolet spectral emission. Growth of InGaN/GaN with more than a 30% indium composition is difficult due to the different MOCVD growth temperature window [2, 33]. High-quality GaN requires a relatively high growth temperature (1050°C), whereas InGaN needs 800°C. Therefore, MOCVD needs high control on temperature fluctuations for better stability growth and to avoid inhomogeneous indium composition. 2.1 Polarization effect: Spontaneous polarization Asymmetry of the wurtzite structure in (0001) sapphire direction (lattice constant c/a < 1.63 A, the electronegativity between Ga and N is vastly different) causes spontaneous polarization in the III-N material system [34]. AlN material has the largest spontaneous polarization compared to GaN and InN, as shown in Figure 4. Theoretical calculation of spontaneous polarization of ternary material can be expressed by [35]: Sp −0.042 x − 0.034 (1 − x ) + 0.037 x (1 − x ) PInxGa 1 − xN = Sp PAlxGa 0.09 x − 0.034 (1 − x ) + 0.019 x (1 − x ) 1− = xN (1) (2) 2.2 Polarization effect: Piezoelectric polarization Piezoelectric polarization effects are generated in the III-N materials system when the heterostructure undergoes huge lattice distortion from biaxial tensile/compressive 5 Light-Emitting Diodes - New Perspectives Figure 4. Spontaneous polarization vs. lattice constant of III-N material system. stress. The generated piezoelectric effect will be in [000–1] (tensile) / [0001] (compressive) direction [29, 36–39]. The piezoelectric effect from III-N ternary material can be calculated from biaxial stress and lattice mismatch. Therefore, piezoelectric polarization can be given as: ( P = 2(e33 ε z + e31 ε x + ε y PZ ) (3) where e33 and e31 are piezoelectric constants and εz is in-plane strain. εz can be calculated from: ( c − c0 ) εz = c0 (4) where c, c0 are in-plane lattice constant and relaxed lattice constant, respectively. 2.3 Quantum-confined stark effect The polarization effect generates an electric field that eventually tilts the conduction and valance bands of InGaN/GaN multi-quantum wells (MQWs). Also, the electric field reduces spatial overlap between holes and electrons waves, thereby reducing the probability of radiative recombination, as shown in Figure 5 [40, 41]. This effect is called QCSE, which highly depends on QW width. When the QW width increases, the QW luminance is red-shifted, whereas it is blue-shifted when the QW width decreases [42–46]. So, the effect of QCSE by polarization should consider two facts on efficient emission: the transition level and luminous intensity of InGaN QW. First, the impact of transition level is a function of several parameters, such as QW width, biaxial stress, growth temperature, sub-band energy levels, etc. Since the spontaneous polarization constant difference is more negligible for GaN and InN, and lattice mismatch is significant, the contribution of piezoelectric polarization is dominant in InGaN ternary alloy. As the lattice mismatch increases, the electron and hole transition level decreases. Secondly, the electroluminescence intensity of InGaN/GaN MQW highly depends on the QW width. Electrons and holes are spatially separated when the QW width increases, reducing the wave function overlap. So, the peak wavelengths have blue-shift and eventually reduce luminescence intensity. 6 Recent Advancements in GaN LED Technology DOI: http://dx.doi.org/10.5772/intechopen.107365 Figure 5. (a) Wurtzite crystal structure of GaN (c-plane), and (b) electron and holes wavefunction separation due to polarization effect. Due to lattice mismatch, huge screw and threading dislocations and point defects will be present in the QW layer. These defects can cause fluctuations that confine carriers in the minimum value of potential energy. Three significant facts potentially vary the localization of carriers and luminescence property of InGaN/GaN LEDs: indium clustering, well width fluctuations, and ternary alloy variations [46–48]. 2.4 Methods to improve green LEDs efficiency using polar surface Epitaxial growth of InGaN/GaN MQW structures on the polar substrate can reach more than 80% internal quantum efficiency (IQE). However, as the wavelength increases, InGaN/GaN-based LEDs’ efficiency decreases by around 30%. Also, the efficiency of green LEDs decreases faster as the current injection increases. This problem leads to improper light mixing efficiency for white LEDs. Therefore, increasing the Figure 6. Optical output power and EQE vs. current densities. 7 Light-Emitting Diodes - New Perspectives efficiency of green LEDs is the primary concern of RGB-LEDs. However, using the existing epitaxial growth technique, few methods can improve the green-based LED IQE, Figure 6 continuous improvisation of epitaxial materials quality with less threading dislocation in the QW region, inserting pre-strain layer to accommodate lattice strain, and sharp QW interface by growth interruption method [29]. On the other hand, growing green LEDs epilayers on non-polar and semipolar substrates reduce the piezoelectric effect at the QW and avoid blue-shifted wave emission. Moreover, it increases the probability of radiative recombination to attain maximum IQE [49, 50]. 3. Recent advancements in non-polar and Semipolar LEDs Many researchers are developing the technology to reduce the piezoelectric polarization electric field effect in the active region of MQW devices. However, few methods have been proposed to increase the quantum efficiency of green LEDs to 163% by introducing a gradient electron blocking layer. 3.1 Non-polar LEDs Several non-polar crystal planes occur in a wurtzite structure orthogonal to the basal planes. The non-polar m-planes {1010} and a-planes {1120} have zero inherent spontaneous polarization effect. InGaN QW grown on non-polar GaN orientation exhibits flat energy bands due to zero strain-induced piezoelectric effect, as shown in Figure 7. The device grown on an m-plane displays high brightness and one hundred times less decay [49, 50]. Researchers at University of California Santa Barbara (UCSB) established violet LEDs based on m-plane, which has low defect density, and the device performance is comparable with c-plane devices [51]. In addition, more uniform current injection, low current droop, and small blue-shift were observed for m-plane-oriented devices [52]. On the other hand, due to the lack of QCSE of non-polar InGaN/GaN MQW, the QW width can be increased without a significant loss in radiative recombination [52, 53]. Figure 7. The m-plane and a-plane of GaN wurtzite crystal structure. Wave function overlaps due to a lack of polarization for better radiative recombination. 8 Recent Advancements in GaN LED Technology DOI: http://dx.doi.org/10.5772/intechopen.107365 However, the growth window for non-polar GaN is narrow and indium incorporation is limited with non-polar InGaN material [49]. Experimentally, it is well proven that growth of m-plane and a-plane GaN on non-polar direction reduces the spontaneous polarization effect. These planes are widely grown on sapphire or silicon substrates which normally shows five times higher (0.5 ~ 0.6 which is equivalent to 1010/cm2) full width half maximum (FWHM) compared to that of grown on c-sapphire substrate. This high FWHM indicates a very high treading dislocation and stacking fault in GaN layer which reduces the crystalline and optical quality of GaN epilayer. Generally, the growth rate in a- or m- direction is lower when compared to c-plane direction. Due to this uneven growth rate the striation is seen in GaN epilayer. During the growth of non-polar GaN, it is important to supress the growth rate in vertical c-plane direction to have smooth morphology by avoiding island formation. The separation of c-plane and enhance of a-plane growth could be achieved in narrow growth temperature window [54–56]. 3.2 Semipolar LEDs The semipolar plane has a growth plane between the c-plane and non-polar plane, as shown in Figure 8. The semipolar plane shows a less polarization electric field effect than the c-plane [39, 57]. Semipolar directional growth has the advantage of high indium incorporation in the InGaN epi layer, which can be used for longer wavelengths. The total polarization and polarization discontinuity between InGaN and GaN will be dependent on the angle between the c-plane and the InGaN epilayer. The motivation of using semipolar plane with different arbitrary angles is to reduce the polarization electric field to suppress the QCSE effect, as shown in Figure 9. Among these semipolar planes, {2021} orientation showed better performance due to high compositional homogeneity across QW [58]. The semipolar directional growth yields a low polarization electric field; however, stacking fault formation is inevitable due to the material’s anisotropy property. The first semipolar LED was demonstrated on {3038} while the first semipolar green LED was demonstrated on GaN along {1013} direction [59, 60]. Currently, the IQE of c-plane-based yellow-green LEDs is surpassed by semipolar Figure 8. Two different Semipolar wurtzite structures of GaN [49]. 9 Light-Emitting Diodes - New Perspectives Figure 9. Polarization discontinuity of GaN for various arbitrary angles with respect to the c-plane [50]. Non-polar Semi-polar Only two different plane orientations Vast variants of planes Gives maximum wave function overlap Substantial wave function overlap (comparatively high than c-plane) Absence of QCSE QCSE effect presents except few planes (e.g 2021 ) Indium is difficult to incorporate which reduces the growth window Indium incorporation is high which enhances the growth window Not suitable for long wavelength emission due to defects in QWs Promising for longer wavelength emission Larger degree of polarized emission Degree of polarization is comparatively less than non-polar Table 1. The important properties of non-polar and semi-polar GaN LEDs devices. long wavelengths of yellow-green LEDs. In 2011, Mg-doped quantum barriers homoepitaxially grown on GaN increased radiative recombination probability to improve green LEDs’ performance [61]. Researchers at UCSB have reported output power of 31.1 mW and 9.9 mW at 20 mA, with EQE of 54% and 20.4% of blue and green LEDs, respectively. These blue and green LEDs were grown on a semipolar growth plane of {1011} and {1122} , respectively [62, 63]. The significant differences between nonpolar and semi-polar based GaN LEDs devices are given in Table 1. 4. Micro LED Display-based LED technology is considered the most promising for next-generation display devices. Every display screen consists of several small fractions known as a pixel, and the size of these pixels determines the resolution of the display screen. The resolution of the display screen is measured in the term of PPI, which means pixel per square inch. We could estimate this PPI term by comparing the resolution 10 Recent Advancements in GaN LED Technology DOI: http://dx.doi.org/10.5772/intechopen.107365 of conventional Organic Light Emitting Diode (OLED) displays and modern smartphones; commercial OLED televisions currently have a pixel density of about 100 to 200 PPI, while the resolution of new smartphones is around 400 to 500 PPI. This pixel density is proportional to the size of a single light emitting unit, which in this case is in the sub-millimeter range. The resolution of the micro-LED display can be increased by fabricating sub-micron LEDs. The individual LEDs would be one pixel for the display, and the size of the LEDs could be reduced according to the desired resolution. In addition, these micro-LEDs have fast response, and are energy efficient than previously developed display technology. The OLED technology, which was developed in the early 90s, was ahead of its time, and during the later decade, it was commercially available in some consumer displays. Its significant advantages over the LCD were self-luminous, wide viewing angle, high contrast, and fast response. On the other hand, these displays were not used widely in consumer electronics [64–66]. This event proved to be a fracture in display technology; major market players and researchers started looking for other materials and technology. However, the main objective remains the same: high contrast, efficiency, resolution, and the process should be well established. Currently, the research is focused on developing micro-LEDs of size <100 μm for high-resolution. Furthermore, according to market research, it is estimated that the micro-LED display market will grow by around 20.5 billion USD in 2025 with an annual growth rate of about 80%. Jiang’s group did the first endeavor for the growth of micro-LED. During their quest, they could fabricate a blue GaN micro-LED chip with an individual pixel diameter of 12 μm [67]. The display made from these pixels measured 0.5 X 0.5 mm2 and had 10 × 10 pixels. Soon after, micro-LED became a hot topic among researchers, leading to the further development of the fabrication technology. Thenceforth, the researchers have extensively understood the nature and epitaxy of III-N material. This has resulted in efficient and complex structures of GaN-based LEDs. Modern LED structures may consist of many layers up to 100 and a lifetime of more than fifty thousand hours. In 2014, Christian et al. fabricated a 50 X 50 μm2 LED and successfully transferred it to a flexible substrate. The fabricated LED emits 60 μW optical power at 1 mA current injection [68]. This research paves the path towards a flexible screen, which overcomes the limitation that III-N micro-LED faced while competing with OLED technology. The color contrast of the micro-LED display is based on three primary colors (red, green, and blue, also called RGB) that can be combined in different ratios to give all colors in nature. Thus, combining three micro-LED (RGB) on a single pixel solves the problem. Figure 10 shows the schematic of such pixel consisting of RGB micro-LEDs. In this arrangement, the different currents would be applied to control the brightness of each LED to realize the combination of RGB primary color to achieve the full-color display. However, integrating three different material LEDs on the same pixel is difficult to mass produce. For example, if there is a need to fabricate a 4 K resolution display, nearly 25 million micro-LEDs are needed to assemble or fabricate. This Figure 10. Schematic of RGB micro-LED full-color pixel. 11 Light-Emitting Diodes - New Perspectives Figure 11. Schematic of InGaN LED structures grown on InGaNOS modified substrate. Figure 12. Schematic of UV micro-LED and QDs integration approach to realize the full-color pixel. hurdle could be overcome by fabricating all LEDs of the same material. The solution is fabricating the GaN/InGaN base LEDs where the emission wavelength could be tuned by varying the molar ration of In in InGaN alloy. The said approach was developed by A. Even et al. used a very innovative substrate to grow InGaN base LEDs. The unique substrate is InGaNOS (InGaN on pseudo-substrate), which overcomes the lattice mismatch and reduces the stress in as-grown films. The epitaxy results show that the grown LED structures could cover blue (482 nm) to red (617 nm) [69]. The schematic is shown in Figure 11. Similarly, Pasayat et al. fabricated an LED structure on GaN porous pseudo substrate. The fabricated LEDs range from 8 x 8 μm2 to 20 x 20 μm2. It was observed that the reduction in size leads to an EL redshift from 525 to 561 nm [70]. As per the study, the color-tunable monolithic integration nitride-based RGB technique can fabricate micro-LED arrays. Another efficient approach was developed by Prof. Kuo, in which the full-color display pixel could be achieved by employing UV LEDs and a down-conversion QDs (Quantum Dots) solution. In this approach, all three pixels are fabricated as AlGaN/ GaN-based UV LED, and QDs are placed above them. The targeted QDs down convert UV emission to respective wavelength, i.e., RGB. The schematic of this approach is shown in Figure 12 [71, 72]. 5. Conclusion We reviewed the history of GaN epitaxy, III-N material improvement strategies, and the advancement of LEDs. It is necessary to reduce the MQW threading dislocation density, QCSE effect, and carrier localization effect to enhance the IQE. To get a high hole concentration by manipulating the Fermi level, we must design strain compensated InGaN/AlInGaN and doped InGaN/GaN barriers. For c-plane growth, ultra-sharp (thickness ~ 3 nm) QW structure with low defect density can yield high IQE. However, for good wavefunction matching and low blue and redshift on the spectral emission, the non-polar and semipolar substrate can be a potential candidate for the reported output power of 31.1 mW and 9.9 mW at 20 mA, with EQE 12 Recent Advancements in GaN LED Technology DOI: http://dx.doi.org/10.5772/intechopen.107365 of 54% and 20.4% of blue and green LEDs, respectively. For non-polar GaN epitaxy of {1120} a-plane and {1010} m-planes can be grown on r-plane Al2O3, a-plane SiC, and m-plane SiC, (100), LiAlO2 are the promising epitaxial substrates. For Semi-polar GaN epitaxy, {2021} orientation on patterned r-plane Al2O3 substrates showed better performance due to their high compositional homogeneity across QW. With the recent developments, GaN is not limited to lighting, but the latest innovation also led to the development of micro-LEDs, laser projection, and point sources. These developments have pushed GaN into the realm of display technology. The miniaturization of the GaN-based micro-LEDs and integration of GaN on silicon will help drive the application into photonic integrated circuits (ICs). Author details Thamer A. Tabbakh1*, Deepak Anandan2, Michael J. Sheldon3, Prashant Tyagi2 and Ahmad Alfaifi4 1 National Center for Nanotechnology and Semiconductor, KACST, Riyadh, Saudi Arabia 2 Skyline Semiconductor Services, Riyadh, Saudi Arabia 3 Orbit Engineering, California, USA 4 Saudi Semiconductors Programm, KACST, Riyadh, Saudi Arabia *Address all correspondence to: [email protected] © 2022 The Author(s). Licensee IntechOpen. This chapter is distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/3.0), which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited. 13 Light-Emitting Diodes - New Perspectives References [1] Seong T-Y, Han J, Amano H, [9] Utsumi W, Saitoh H, Kaneko H, Morkoc H, editors. III-Nitride Based Light Emitting Diodes and Applications. Vol. 126. Dordrecht: Springer Netherlands; 2013. DOI: 10.1007/978-94-007-5863-6 Watanuki T, Aoki K, Shimomura O. Congruent melting of gallium nitride at 6 GPa and its application to singlecrystal growth. Nature Materials. 2003;2(11):735-738. DOI: 10.1038/ nmat1003 [2] Ambacher O. Growth and applications of group III-nitrides. Journal of Physics D: Applied Physics. 1998;31(20):26532710. DOI: 10.1088/0022-3727/31/20/001 [3] Strite S. GaN, AlN, and InN: A review. Journal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures. 1992;10(4):1237. DOI: 10.1116/1.585897 [4] Cho J, Park JH, Kim JK, Schubert EF. White light-emitting diodes: History, progress, and future: White lightemitting diodes. Laser & Photonics Reviews. 2017;11(2):1600147. DOI: 10.1002/lpor.201600147 [5] Chen Y et al. GaN in different dimensionalities: Properties, synthesis, and applications. Materials Science & Engineering R: Reports. 2019;138:60-84. DOI: 10.1016/j.mser.2019.04.001 [10] Porowski S, Grzegory I. Thermodynamical properties of III–V nitrides and crystal growth of GaN at high N2 pressure. Journal of Crystal Growth. 1997;178(1-2):174-188. DOI: 10.1016/S0022-0248(97)00072-9 [11] Karpiński J, Jun J, Porowski S. Equilibrium pressure of N2 over GaN and high pressure solution growth of GaN. Journal of Crystal Growth. 1984;66(1):110. DOI: 10.1016/0022-0248(84)90070-8 [12] Grandjean N, Massies J, Leroux M. Nitridation of sapphire. Effect on the optical properties of GaN epitaxial overlayers. Applied Physics Letters. 1996;69(14):2071-2073. DOI: 10.1063/1.116883 [13] Heinlein C, Grepstad J, Berge T, editors. Handbook of Optics. 2nd ed. New York: McGraw-Hill; 1995 Riechert H. Preconditioning of c-plane sapphire for GaN epitaxy by radio frequency plasma nitridation. Applied Physics Letters. 1997;71(3):341-343. DOI: 10.1063/1.119532 [7] Yoshida H, Kuwabara M, Yamashita Y, [14] Dixit R et al. Influence of growth Uchiyama K, Kan H. The current status of ultraviolet laser diodes: The current status of ultraviolet laser diodes. Physica Status Solidi A: Applications and Materials Science. 2011;208(7):15861589. DOI: 10.1002/pssa.201000870 temperature on laser molecular beam epitaxy and properties of GaN layers grown on c-plane sapphire. Optical Materials. 2017;66:142-148. DOI: 10.1016/j.optmat.2017.01.053 [6] Bass M, Optical Society of America, [15] Tyagi P et al. Dependence of Al [8] Amano H et al. The 2018 GaN power electronics roadmap. Journal of Physics D: Applied Physics. 2018;51(16):163001. DOI: 10.1088/1361-6463/aaaf9d 14 incorporation on growth temperature during laser molecular beam epitaxy of AlxGa1−xN epitaxial layers on sapphire (0001). Journal of Alloys Recent Advancements in GaN LED Technology DOI: http://dx.doi.org/10.5772/intechopen.107365 and Compounds. 2018;739:122-128. DOI: 10.1016/j.jallcom.2017.12.220 film using an AlN buffer layer. Applied Physics Letters. 1986;48(5):353-355. DOI: 10.1063/1.96549 [16] Johnson WC, Parson JB, Crew MC. Nitrogen compounds of gallium. III. The Journal of Physical Chemistry. 1932;36(10):2651-2654. DOI: 10.1021/ j150340a015 [17] Maruska HP, Tietjen JJ. THE PREPARATION AND PROPERTIES OF VAPOR-DEPOSITED SINGLECRYSTAL-LINE GaN. Applied Physics Letters. 1969;15(10):327-329. DOI: 10.1063/1.1652845 [18] Manasevit HM, Simpson WI. The use of metal-organics in the preparation of semiconductor materials. Journal of the Electrochemical Society. 1969;116(12):1725. DOI: 10.1149/1.2411685 [19] Kim W, Botchkarev AE, Salvador A, Popovici G, Tang H, Morkoç H. On the incorporation of Mg and the role of oxygen, silicon, and hydrogen in GaN prepared by reactive molecular beam epitaxy. Journal of Applied Physics. 1997;82(1):219-226. DOI: 10.1063/1.365801 [20] Seifert W, Franzheld R, Butter E, Sobotta H, Riede V. On the origin of free carriers in high-conducting n-GaN. Crystal Research and Technology. 1983;18(3):383-390. DOI: 10.1002/ crat.2170180314 [21] Yoshida S, Misawa S, Gonda S. Improvements on the electrical and luminescent properties of reactive molecular beam epitaxially grown GaN films by using AlN-coated sapphire substrates. Applied Physics Letters. 1983;42(5):427-429. DOI: 10.1063/1.93952 [23] Nakamura S. GaN growth using GaN buffer layer. Japanese Journal of Applied Physics. 1991;30(Part 2, 10A):L1705-L1707. DOI: 10.1143/JJAP.30. L1705 [24] Amano H, Kito M, Hiramatsu K, Akasaki I. P-type conduction in Mg-doped GaN treated with low-energy electron beam irradiation (LEEBI). Japanese Journal of Applied Physics. 1989;28(Part 2, 12):L2112-L2114. DOI: 10.1143/JJAP.28.L2112 [25] Nakamura S, Mukai T, Senoh M, Iwasa N. Thermal annealing effects on P-type Mg-doped GaN films. Japanese Journal of Applied Physics. 1992;31(Part 2, 2B):L139-L142. DOI: 10.1143/JJAP.31. L139 [26] Nakamura S, Krames MR. History of gallium–nitride-based light-emitting diodes for illumination. Proceedings of the IEEE. 2013;101(10):2211-2220. DOI: 10.1109/JPROC.2013.2274929 [27] Nakamura S, Mukai T. High-quality InGaN films grown on GaN films. Japanese Journal of Applied Physics. 1992;31(Part 2, 10B):L1457-L1459. DOI: 10.1143/JJAP.31.L1457 [28] Nam OH et al. Characteristics of GaN-based laser diodes for post-DVD applications. Physica Status Solidi (a). 2004;201(12):2717-2720. DOI: 10.1002/ pssa.200405114 [29] Wallace M. Optoelectronic Study of InGaN/GaN LEDs. [Thesis]. University of Strathclyde; 2016. DOI: 10.48730/43Q0ZY87. Available from: https://stax.strath. ac.uk/concern/theses/nv935295j [22] Amano H, Sawaki N, Akasaki I, Toyoda Y. Metalorganic vapor phase epitaxial growth of a high quality GaN 15 [30] Amano H. Nobel lecture: Growth of GaN on sapphire via low-temperature Light-Emitting Diodes - New Perspectives deposited buffer layer and realization of p -type GaN by Mg doping followed by low-energy electron beam irradiation. Reviews of Modern Physics. 2015;87(4):1133-1138. DOI: 10.1103/ RevModPhys.87.1133 [37] Deng Y et al. Study on strain and [31] Shimada J, Kawakami Y, Fujita S. [38] Romanov AE, Baker TJ, Nakamura S, piezoelectric polarization of AlN thin films grown on Si. Journal of Vacuum Science & Technology A: Vacuum, Surfaces, and Films. 2005;23(4):628-630. DOI: 10.1116/1.1927533 Development of lighting goggles with power white LED modules. In: Proceedings of SPIE - SPIE Digital Library. San Jose, CA. 2003. p. 174. DOI: 10.1117/12.476558 Speck JS, ERATO/JST UCSB Group. Strain-induced polarization in wurtzite III-nitride semipolar layers. Journal of Applied Physics. 2006;100(2):023522. DOI: 10.1063/1.2218385 [32] Haitz R, Kish F, Tsao J, Nelson J. The [39] Gil B, Bigenwald P, Briot O. Case for a National Research Program on Semiconductor Lighting. Sandia Report SAND-2000 1612. 2000. Available from: https://www.sandia.gov/app/ uploads/sites/153/2021/12/hpsnl_sand_ report_2000.pdf Polarization fields in wurtzite strained layers grown on () planes. Superlattices and Microstructures. 2008;44(3):291301. DOI: 10.1016/j.spmi.2008.06.003 [33] Dupuis RD. Epitaxial growth of III–V nitride semiconductors by metalorganic chemical vapor deposition. Journal of Crystal Growth. 1997;178(1-2):56-73. DOI: 10.1016/S0022-0248(97)00079-1 [34] Bernardini F, Fiorentini V, Vanderbilt D. Spontaneous polarization and piezoelectric constants of III-V nitrides. Physical Review B. 1997;56(16):R10024-R10027. DOI: 10.1103/PhysRevB.56.R10024 [35] Bernardini F, Fiorentini V. [40] Della Sala F et al. Free-carrier screening of polarization fields in wurtzite GaN/InGaN laser structures. Applied Physics Letters. 1999;74(14):2002-2004. DOI: 10.1063/1.123727 [41] Seo Im J, Kollmer H, Off J, Sohmer A, Scholz F, Hangleiter A. Reduction of oscillator strength due to piezoelectric fields in G a N/a l x Ga 1 − x N quantum wells. Physical Review B. 1998;57(16):R9435-R9438. DOI: 10.1103/ PhysRevB.57.R9435 [42] Peter M, Laubsch A, Stauss P, Nonlinear behavior of spontaneous and piezoelectric polarization in III-V nitride alloys. Physica Status Solidi A: Applications and Materials Science. 2002;190(1):65-73. DOI: 10.1002/ 1521-396X(200203)190:1<65::AIDPSSA65>3.0.CO;2-0 Walter A, Baur J, Hahn B. Green ThinGaN power-LED demonstrates 100 lm. Physica Status Solidi C: Current Topics in Solid State Physics. 2008;5(6):2050-2052. DOI: 10.1002/ pssc.200778554 [36] Doshi B, Brennan KF, Bicknell- laser diodes. Physica Status Solidi A: Applications and Materials Science. 2010;207(6):1318-1322. DOI: 10.1002/ pssa.200983620 Tassius R, Grunthaner F. The effect of strain-induced polarization fields on impact ionization in a multiquantumwell structure. Applied Physics Letters. 1998;73(19):2784-2786. DOI: 10.1063/1.122590 16 [43] Lutgen S et al. True green InGaN [44] Queren D et al. 500 nm electrically driven InGaN based laser diodes. Applied Recent Advancements in GaN LED Technology DOI: http://dx.doi.org/10.5772/intechopen.107365 Physics Letters. 2009;94(8):081119. DOI: 10.1063/1.3089573 [45] Queren D et al. Quality and thermal stability of thin InGaN films. Journal of Crystal Growth. 2009;311(10):2933-2936. DOI: 10.1016/j.jcrysgro.2009.01.066 [52] Ling S-C, Lu T-C, Chang S-P, Chen J-R, Kuo H-C, Wang S-C. Low efficiency droop in blue-green m-plane InGaN/ GaN light emitting diodes. Applied Physics Letters. 2010;96(23):231101. DOI: 10.1063/1.3449557 [53] Lin Y-D et al. Characterization [46] Brillson LJ, Levin TM, Jessen GH, Ponce FA. Localized states at InGaN/ GaN quantum well interfaces. Applied Physics Letters. 1999;75(24):3835-3837. DOI: 10.1063/1.125472 of blue-green m-plane InGaN light emitting diodes. Applied Physics Letters. 2009;94(26):261108. DOI: 10.1063/1.3167824 [54] Cai Y, Shen S, Zhu C, Zhao X, Bai J, [47] Golub LE et al. Low-temperature kinetics of localized excitons in quantum-well structures. Physica Status Solidi B: Basic Solid State Physics. 1998;205(1):203-208. DOI: 10.1002/ (SICI)1521-3951(199801)205:1<203: AID-PSSB203>3.0.CO;2-N Wang T. Nonpolar (112̅0) GaN metal– semiconductor–metal photodetectors with superior performance on silicon. ACS Applied Materials & Interfaces. 2020;12(22):25031-25036. DOI: 10.1021/ acsami.0c04890 [55] Izyumskaya N et al. Epitaxial lateral [48] Na JH et al. Dependence of carrier localization in InGaN∕GaN multiplequantum wells on well thickness. Applied Physics Letters. 2006;89(25):253120. DOI: 10.1063/1.2423232 overgrowth of non-polar GaN(11̄00) on Si(112) patterned substrates by MOCVD. Journal of Crystal Growth. 2011;314(1):129-135. DOI: 10.1016/j. jcrysgro.2010.11.152 [49] Li J et al. III-Nitrides Light Emitting [56] Jiu L, Gong Y, Wang T. Overgrowth Diodes: Technology and Applications. Vol. 306. Singapore: Springer Singapore; 2020. DOI: 10.1007/978-981-15-7949-3 and strain investigation of (1120) non-polar GaN on patterned templates on sapphire. Scientific Reports. 2018;8(1):9898. DOI: 10.1038/ s41598-018-28328-7 [50] Kelchner KM, DenBaars SP, Speck JS. GaN laser diodes on nonpolar and Semipolar planes. In: Semiconductors and Semimetals. Vol. 86. Elsevier; 2012. pp. 149-182. DOI: 10.1016/ B978-0-12-391066-0.00004-6 [51] Yamada H et al. Comparison of InGaN/GaN light emitting diodes grown on m -plane and a -plane bulk GaN substrates: Comparison of InGaN/GaN light emitting diodes grown on m -plane and a -plane bulk GaN substrates. Physics Status Solidi RRL - Rapid Research Letter. 2008;2(2):89-91. DOI: 10.1002/ pssr.200701313 17 [57] Takeuchi T, Amano H, Akasaki I. Theoretical study of orientation dependence of piezoelectric effects in Wurtzite strained GaInN/GaN Heterostructures and quantum Wells. Japanese Journal of Applied Physics. 2000;39(Part 1, 2A):413-416. DOI: 10.1143/JJAP.39.413 [58] Ueno M et al. InGaN-based true green laser diodes on novel semipolar GaN substrates. Journal of Crystal Growth. 2011;315(1):258-262. DOI: 10.1016/j.jcrysgro.2010.07.016 Light-Emitting Diodes - New Perspectives [59] Kamiyama S et al. GaN growth [67] Jiang HX, Jin SX, Li J, Shakya J, on (30&3macr,8) 4H-SiC substrate for reduction of internal polarization. Physica Status Solidi C: Current Topics in Solid State Physics. 2005;2(7):2121-2124. DOI: 10.1002/pssc.200461390 Lin JY. III-nitride blue microdisplays. Applied Physics Letters. 2001;78(9):13031305. DOI: 10.1063/1.1351521 [60] Sharma R et al. Demonstration of a semipolar (101¯3¯) InGaN∕GaN green light emitting diode. Applied Physics Letters. 2005;87(23):231110. DOI: 10.1063/1.2139841 [61] Huang C-Y et al. Influence of Mg-doped barriers on semipolar (202¯1) multiple-quantum-well green light-emitting diodes. Applied Physics Letters. 2011;99(14):141114. DOI: 10.1063/1.3647560 [62] Zhao Y et al. 30-mW-class high- power and high-efficiency blue Semipolar (10\bar1\bar1) InGaN/ GaN light-emitting diodes obtained by backside roughening technique. Applied Physics Express. 2010;3(10):102101. DOI: 10.1143/APEX.3.102101 [63] Yamamoto S et al. High-efficiency single-quantum-well green and yellowgreen light-emitting diodes on Semipolar (20\bar21) GaN substrates. Applied Physics Express. 2010;3(12):122102. DOI: 10.1143/APEX.3.122102 [64] Geffroy B, le Roy P, Prat C. Organic light-emitting diode (OLED) technology: Materials, devices and display technologies. Polymer International. 2006;55(6):572-582. DOI: 10.1002/pi.1974 [65] Chen H, Tan G, Wu S-T. Ambient contrast ratio of LCDs and OLED displays. Optics Express. 2017;25(26):33643. DOI: 10.1364/OE.25.033643 [66] Wu T et al. Mini-LED and micro- LED: Promising candidates for the next generation display technology. Applied Sciences. 2018;8(9):1557. DOI: 10.3390/ app8091557 18 [68] Goßler C et al. GaN-based micro-LED arrays on flexible substrates for optical cochlear implants. Journal of Physics D: Applied Physics. 2014;47(20):205401. DOI: 10.1088/0022-3727/47/20/205401 [69] Even A et al. Enhanced In incorporation in full InGaN heterostructure grown on relaxed InGaN pseudo-substrate. Applied Physics Letters. 2017;110(26):262103. DOI: 10.1063/1.4989998 [70] Pasayat SS et al. Color-tunable < 10μm square InGaN micro-LEDs on compliant GaN-on-porousGaN pseudo-substrates. Applied Physics Letters. 2020;117(6):061105. DOI: 10.1063/5.0011203 [71] Han H-V et al. Resonant-enhanced full-color emission of quantum-dotbased micro LED display technology. Optics Express. 2015;23(25):32504. DOI: 10.1364/OE.23.032504 [72] Lin H-Y et al. Optical cross-talk reduction in a quantum-dot-based fullcolor micro-light-emitting-diode display by a lithographic-fabricated photoresist mold. Photonics Research. 2017;5(5):411. DOI: 10.1364/PRJ.5.000411