Chemistry

The adsorption of fluorescein dye (FD) on wild herb microparticles (Juniperus (JH) and Solenostemma argel (Del) Hayne (SH)) was studied to elucidate the changes in adsorption behavior with various parameters, such as initial concentration, adsorbent dosage, pH, contact time, and temperature. It was determined that the adsorption percentage of JH for FD was as high as 85.5%, which was higher than that of SH (71.9%). The morphologies of JH and SH were analyzed using Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and scanning electron microscopy (SEM) analyses. The JH and SH adsorbents contained different functional groups, which were involved in the binding of the FD molecules during adsorption. The XRD patterns of JH and SH confirmed the presence of a combination of amorphous and crystalline phases in their structures. The SEM images of the surface of JH revealed the presence of deep pores ranging in size from 1.9 to 3.5 μm, while SH contained smaller pores ...

Corrosion inhibition of steel in phosphoric acid (H 3 PO 4) by thiosemicarbazide derivatives was studied using different chemical and electrochemical techniques. Protection efficiency up to 99% was obtained with small amounts (10-4 M) of cinnamaldehyde thiosemicarbazone (CTSCN). The order of increasing inhibition efficiency was correlated with the modification of the molecular structure of the inhibitors. Empirical kinetic relationship was obtained describing the experimental data obtained from the different compounds used in this investigation. Potentiodynamic polarization curves indicated that the compounds acted primarily as mixed-type inhibitors. Electrochemical impedance spectroscopy showed that the charge-transfer resistance increased and the capacitance of the double layer decreased with increasing the concentration of the inhibitor in the medium, confirming adsorption process mechanism. At high concentrations (> 10 4 M), the capacitance of the double layer leveled off since maximum double-layer thickness was attained. Kinetic-thermodynamic model and Flory-Huggins adsorption isotherm described the experimental findings. Number of active sites, binding constant, and change of free energy were computed for all inhibitors studied. Based on the inhibitor, it was found that each organic molecule replaced one or more adsorbed water molecule from the steel surface. The influence of exposure time on the performance of crotonaldehyde thiosemicarbazone (CrTSCN) was studied. Results showed that the inhibitor performed better with time and at a critical concentration of 5 x 10-4 M. Maximum protection efficiency was attained because of a strong adsorption on steel surface over the total period of immersion exceeding 30 h.

Carbon steel is widely used in industries due to its good mechanical properties carbon steel it has been extensively used under different conditions in chemical and allied industries in presence of alkaline, acid and salt solutions. The investigation of corrosion of carbon steel is always a subject of high theoretical as well as practical interest. Chloride, sulphate and nitrate ions in aqueous media are particularly aggressive and

In this study, the adsorption of malachite green (MG) onto date palm fibers (DPF) was examined in aqueous solutions. The Langmuir and Freundlich adsorption isotherm models were employed to describe the equilibrium adsorption data. The Freundlich isotherm model was found to fit the adsorption data The removal percentage of MG dye from aqueous solutions via adsorption onto DPF adsorbent varied with pH and temperature, showing that these factors play a key role in the adsorption process. The removal percentage was found to increase with decrease in the solution temperature and in alkaline media. The adsorption kinetic data were fitted with a pseudo-secondorder model.

Wild herbs (Equisetum, EH and Teucrium, TH) were used as environment friendly adsorbents in the present study. This study focuses on the investigation of the adsorption ability of Co, Cd and Li from aqueous solution. The adsorption of heavy metals onto EH and TH was dependent on particle size, dose, solution pH, contact time, and temperature. Kinetic data were tested using pseudo-first-order and pseudo-secondorder kinetic models. The best fit was obtained with the pseudo-second-order kinetic model. Langmuir and Freundlich models have been applied to calculate adsorption data and the thermodynamic parameters; entropy, DS°, enthalpy, DH°, and the Gibbs free energy, DG°; were determined. The results suggests that the adsorption of heavy metals by the wild herbs are endothermic and a spontaneous process. Thus, it was concluded that EH and TH are promising adsorbents for the adsorption of heavy metals from aqueous solutions.

Novel Zr 2 Ni 1 Cu 7 trimetallic nano-alloy (TNA) and Zr 2 Ni 1 Cu 7 /Si 3 N 4 trimetallic nano-alloy composite (TNAC) have been successfully prepared by facile microwave reduction method. The synthesis of TNA and TNAC was ascertained by characterizing them by using various techniques such as SEM, TEM, XRD, EDX and FTIR etc. The EDX shows the presence of all constituents in TNA and TNAC. The XRD study demonstrated the crystalline and semi-crystalline nature of TNA and TNAC. The optical band gap study revealed that TNAC (2.47 eV) has lower band gap then TNA (2.54 eV). The visible light photocatalytic activity of Zr 2 Ni 1 Cu 7 TNA and Zr 2 Ni 1 Cu 7 /Si 3 N 4 TNAC has been successfully utilized for the photodegradation of methylene blue (MB). The presence of H 2 O 2 has been found to influence the photodegradation rate. Photodegradation results presented that maximum degradation was observed in the presence of H 2 O 2 and Zr 2 Ni 1 Cu 7 TNAC (92%). Scavenging activity has revealed that the hydroxyl radicals were the major reacting species. These species successfully degraded the MB into various intermediates that has successfully been determined by the LC-MS. Kinetic studies indicated that the degradation of MB by Zr 2 Ni 1 Cu 7 TNA and Zr 2 Ni 1 Cu 7 /Si 3 N 4 TNAC followed pseudo-first-order kinetics.

In this study, extracts of both treated and untreated date palm tree waste were used as inhibitors of carbon steel corrosion in 1 M HCl. The date palm wastes used were the fiber and leaflets of the plant, and the treatment process involved gum arabic solution. The electrochemical measurements showed that the extracts were efficient inhibitors. The treated wastes were more efficient inhibitors than untreated waste, and the leaflets were better inhibitors than the fibers. The effect of temperature on inhibition efficiency, thermodynamic parameters, and adsorption isotherms for the treated inhibitors were studied. It was found that the adsorption was endothermic, occurred spontaneously, and that the adsorption data fit Langmuir isotherm model.

Wild herbs (Origanum (OR) and Lavandula (LV)) were used as environment-friendly adsorbents in this study. The adsorbents were used for adsorption of Cu and Ba from water. The adsorption of heavy metals onto OR and LV was dependent on particle size, dose, and solution pH. The diameter of adsorbent particles was less than 282.8 nm. The adsorption follows second-order kinetics. Langmuir and Freundlich models have been applied to describe the equilibrium data, and the thermodynamic parameters, the Gibbs free energy, ∆G°, enthalpy, ∆H°, and entropy, ∆S°, have been determined. The positive value of ∆H° suggests that the adsorption of heavy metals by the wild herbs is endothermic. The negative values of ∆G° at all the studied temperatures indicate that the adsorption is a spontaneous process. It can be concluded that OR and LV are promising adsorbents for the removal of heavy metals from aqueous solutions over a range of concentrations.

This is a PDF file of an article that has undergone enhancements after acceptance, such as the addition of a cover page and metadata, and formatting for readability, but it is not yet the definitive version of record. This version will undergo additional copyediting, typesetting and review before it is published in its final form, but we are providing this version to give early visibility of the article. Please note that, during the production process, errors may be discovered which could affect the content, and all legal disclaimers that apply to the journal pertain.

CoO/Co3O4 nanoparticles (NPs) were synthesized by using a fresh egg white-assisted combustion method which acts as a new approach for green synthesis of this composite. This method was carried out by the direct heat of cobalt precursor with egg white at low temperature for very short period. In fact, this route is a novel, cheap and appropriate technique yielding nanoparticle-based materials. CoO/Co3O4 nanoparticles were characterized by examining the structure and identifying the elements and determining the morphology via XRD, FTIR, SEM, EDS and TEM techniques. The sample magnetic observations were measured through the use of a vibrating sample magnetometer (VSM). The results of XRD, EDS, SEM and TEM confirmed the positive synthesis of the cubic CoO/Co3O4 NPs with sponge crystals which proceed. For the as synthesized composite, 57.75 m2/g, 0.0148 cc/g and 10.31 nm were identified to be the SBET, Vp and ȓ, respectively. The cobalt oxide particles in their nature were polycrystallin...

The adsorption of Cu2+ ions from an aqueous solution using AgNPs synthesized from Convolvulus arvensis leaf extract was investigated. The characterization of AgNPs was investigated before and after the adsorption of Cu2+ ions via Fourier-transform infrared spectroscopy (FTIR), energy-dispersive X-ray spectroscopy (EDS), and scanning electron microscopy (SEM) analyses. The adsorbent contained various functional groups in addition to the AgNPs, which contributed to the Cu2+ ions adsorption. The silver nanoparticle surface consisted of spherical particles and deep pores, which adsorbed numerous Cu2+ ions. The influences of dosage, pH, and contact time on adsorption of 10 and 50 mg/L Cu2+ at 298 K, and initial Cu2+ concentrations at 298 and 323 K were studied. It was found that the highest percentage of Cu2+ ions adsorbed from an aqueous solution was 98.99%; the aqueous solution had 10 mg/L of Cu2+ ions and 0.2 g of AgNPs, at pH 12 and 298 K. A pseudo-second kinetics model offered the m...

A series of copper-based systems containing two different nanocomposites (Cu2O/CuO and Cu2O/Cu) was synthesized by the egg white assisted auto-combustion route. This method was distinguished by the simplicity of its steps, low cost, one-pot synthesis process at low temperature and, short time. The characterization of the as prepared nanocomposites was carried out by using X-ray diffraction (XRD), Fourier-transform infrared (FTIR), Scanning electron microscope (SEM) and transmission electron micrograph (TEM), Energy dispersive spectrometry (EDS) techniques. Surface and magnetic properties of the obtained systems were determined by using N2 adsorption/desorption isotherms at 77 K and the vibrating sample magnetometer (VSM) technique. XRD results confirmed the formation of Cu2O/CuO and Cu2O/Cu nanocomposites with different ratios of well crystalline CuO, Cu2O, and Cu phases. FTIR results of the combusted product displays the presence of both CuO and Cu2O, respectively. SEM/EDS and TEM ...

Magnetic Ni-Mn mixed oxides based on nanoparticles (NPs) have been developed at 700 °C using a ceramic method and a glycine-assisted auto combustion path. The thermogravimetry–derivative thermogravimetry (TG—DTG), infrared radiation (IR), X-ray powder diffraction (XRD), energy-dispersive X-ray spectroscopy (EDX) and high resolution transmittance electron micrographs (HRTEM) techniques have been used to characterize as synthesized nanomaterials by evaluating their thermal behavior, structure, distinguishing the components and establishing the morphology. A vibrating sample magnetometer has been used to estimate the magnetic properties of the materials (VSM). The analyses indicate that using a glycine-assisted auto combustion method resulted in formation of cubic spinel NiMn2O4 NPs as a single phase. The ceramic process, from the other side, led to the development of Mn2O3/NiMnO3/NiMn2O4 nanocomposite. The resulting particles being polycrystalline, including average sizes ranging from...

Egg white-induced auto combustion has been used to synthesize undoped and Fe-doped CuO/Cu2O/Cu4O3 nanocomposites in a soft, secure, and one-pot procedure. X-ray powder diffraction (XRD) and Fourier transform infrared (FTIR) investigations have been used to identify functional groups and the structural properties of crystalline phases present in the as-synthesized composites. Scanning Electron Microscopy/Energy Dispersive Spectrometry (SEM/EDS) elemental mapping analyses and Transmission Electron Microscopy (TEM) techniques were used to explore the morphological and compositional properties of these composites. N2-adsorption/desorption isotherm models have been used to examine the surface variables of the as-prepared systems. Based on the Vibrating Sample Magnetometer (VSM) technique, the magnetic properties of various copper-based nanocomposites were detected due to being Fe-doped. XRD results showed that the undoped system was composed of CuO as a major phase with Cu2O and Cu4O3 as...

The preparation of copper manganite (hopcalite, Cu1.5Mn1.5O4), as a single phase, was achieved by using a sustainable method of green synthesis. This method is based on the replacement of the conventional “brute force” ceramic preparation by the recent “soft force” green synthesis via the egg white assisted one-step method. In other words, we present a facile and rapid methodology to prepare the nanocrystalline Cu1.5Mn1.5O4 spinel as a single phase, compared to our previous work using ceramic and glycine-assisted combustion methods. The as-synthesized copper manganite was characterized using X-ray diffraction (XRD), Fourier-transform infrared (FTIR), energy-dispersive spectroscopy (EDS), and scanning electron microscope (SEM). We used a vibrating sample magnetometer to determine the magnetic properties of the prepared sample (VSM). XRD, FTIR, SEM, EDS and transmittance electron micrograph (TEM) resulted in synthesis of a successful cubic spinel Cu1.5Mn1.5O4 system with a sponge crys...

Nanosized Ni ferrite has been prepared by an ecofriendly green synthesis approach based on the self-combustion method. In this route, the egg white as a green fuel was employed with two different amounts (3 and 10 mL). The XRD results display the formation of a stoichiometric NiFe2O4-type inverse spinel structure with a lattice parameter located at 0.8284 nm and 0.8322 nm. Additionally, the nickel ferrites’ typical crystallite size, as synthesized, ranged between 4 and 18 nm. Indicating the development of ferrite material, FTIR analysis shows two distinctive vibrational modes around 600 cm−1 and 400 cm−1. TEM measurements show the formation of nanosized particles with semispherical-type structure and some agglomerations. As the egg white concentration rises, the surface area, total pore volume, and mean pore radius of the material, as prepared, all decrease, and according to the surface area parameters discovered using BET analysis. Based on VSM analysis, the values of saturation ma...

A series of virgin and lithia-doped Ni ferrites was synthesized using egg-white-mediated combustion. Characterization of the investigated ferrites was performed using several techniques, specifically, X-ray Powder Diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), and High-resolution transmission electron microscopy (HRTEM). XRD-based structural parameters were determined. A closer look at these characteristics reveals that lithia doping enhanced the nickel ferrite lattice constant (a), unit cell volume (V), stress (ε), microstrain (σ), and dislocation density (δ). It also enhanced the separation between magnetic ions (LA and LB), ionic radii (rA, rB), and bond lengths (A-O and B-O) between tetrahedral (A) and octahedral (B) locations. Furthermore, it enhanced the X-ray density (Dx) and crystallite size (d) of random spinel nickel ferrite displaying opposing patterns of behavior. FTIR-based functional groups of random spinel nickel ferrite were determined. HRTEM-base...

In this study, we have used a mild pyrolytic process for the synthesis of luminescent carbon material from phalsa (Grewia asiatica Linn) and utilized it for the photodegradation of methylene blue (MB) in aqueous solution under the irradiation of ultraviolet (UV) light. The carbon material was found to be graphitic in nature and with carbon dot-like properties as demonstrated by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), dynamic light scattering (DLS), and UV-visible techniques. The prepared carbon material was further studied for the elucidation of functional groups through Fourier transform infra-red (FTIR) spectroscopy. The carbon material exhibits the nanostructured phase which makes it a high surface area material for useful surface reactions. Different photodegradation aspects were investigated, such as initial dye concentration, catalyst dose, effect of pH of dye solution, reusability, electrochemical active surface area (ECSA), and charge transfer and...

This study aims to develop a self-combustion method for use in the preparation of copper and cobalt ferrites. This development was based on the full use of dry leaves of Corchorus olitorius plant in order to stimulate the preparation of the studied ferrites by making full use of the small amount of carbon produced from the combustion process. The fabrication of CuFe2O4 and CoFe2O4 with spinel-type structures and the Fd3m space group is confirmed by XRD and FTIR investigations. Two major vibration bands occur laterally at 400 cm−1 and 600 cm−1. We were able to understand the existence of two stages through the thermal behavior based on TG-DTG analysis for the materials under investigation. The first is from room temperature to 600 °C, which indicates the formation of reacting oxides with Co or Cu ferrites, while the second is from 600–1000 °C, which indicates the growth in the ferrite fabrication. The surface morphological analyses (SEM/EDS and TEM) display formation of homogeneous a...