ABSTRACT Forest biomass is a renewable and sustainable source of energy that can be used for prod... more ABSTRACT Forest biomass is a renewable and sustainable source of energy that can be used for producing electricity, heat, and biofuels. The production of biomass for energy is considered to be an important step in developing sustainable communities and managing greenhouse gas emissions effectively. Biomass properties vary and are commonly associated with plant species. Hence, efficient methods to predict biofuel characteristics will greatly affect the utilization and management of feedstock production. In this paper attempt was made to correlate various chemical characteristics with NIR spectra. Wood chips from various plant species was analyzed for lignin content, heating value, ash content and NIR and the results were evaluated with correlation, PCA and PCR. Initial evaluation showed promising results where chemical components in the wood correlate to NIR spectra. A selection of results will be presented in this paper. Further analysis as well as results from PCA and PCR models will be presented in the full paper version.
This paper presents experimental data concerning combustion characteristics of full-scale biomass... more This paper presents experimental data concerning combustion characteristics of full-scale biomass-fired bubbling fluidized bed (BFB) steam boiler with a thermal output of 31 MW. The purpose of the experimental measurements is to show how the values of selected combustion parameters vary in reality depending on measurement position. Experimentation involves specifically a determination of combustion gas temperature and concentration of gas species i.e. O 2 , CO 2 , CO and NO X at different positions in the furnace and the flue gas trains. Character of results from the furnace indicates the intermediate stage of thermochemical reactions. Increased levels of CO close to the wall have been found, this may be indicating reducing atmosphere and thereby increased corrosion risk. Results from flue gas trains demonstrate that behavior there is related to the fluid dynamics and heat transfer, the temperature is too low for further combustion reactions. Results show great variations among measured values of all measurands depending on a distance along the line from the wall to the center of the boiler. The measurements from permanently installed fixed sensors are not giving value representing average conditions, but overall profiles can be correlated to online measurements from fixed sensors.
6th IFAC Symposium on Power Plants and Power Systems Control (2009), 2009
ABSTRACT This paper covers a method for operator decision support, where physical simulation mode... more ABSTRACT This paper covers a method for operator decision support, where physical simulation models are used to connect different physical variables to each other. By comparing energy and material balances for a larger process area inconsistencies in single process parts and sensor measurements can be detected, by following the development between single measurements and values predicted from the simulations. This information then can be used as input to e.g. a BN, Bayesian Network, for decision support. The application has been for a CFB boiler at Mälarenergi AB. The simulators have been made in Modelica respectively a more advanced model in APROS.
This paper presents experimental data concerning combustion characteristics of full-scale biomass... more This paper presents experimental data concerning combustion characteristics of full-scale biomass-fired bubbling fluidized bed (BFB) steam boiler with a thermal output of 31 MW. The purpose of the experimental measurements is to show how the values of selected combustion parameters vary in reality depending on measurement position. Experimentation involves specifically a determination of combustion gas temperature and concentration of gas species i.e. O 2 , CO 2 , CO and NO X at different positions in the furnace and the flue gas trains. Character of results from the furnace indicates the intermediate stage of thermochemical reactions. Increased levels of CO close to the wall have been found, this may be indicating reducing atmosphere and thereby increased corrosion risk. Results from flue gas trains demonstrate that behavior there is related to the fluid dynamics and heat transfer, the temperature is too low for further combustion reactions. Results show great variations among measured values of all measurands depending on a distance along the line from the wall to the center of the boiler. The measurements from permanently installed fixed sensors are not giving value representing average conditions, but overall profiles can be correlated to online measurements from fixed sensors.
ABSTRACT Forest biomass is a renewable and sustainable source of energy that can be used for prod... more ABSTRACT Forest biomass is a renewable and sustainable source of energy that can be used for producing electricity, heat, and biofuels. The production of biomass for energy is considered to be an important step in developing sustainable communities and managing greenhouse gas emissions effectively. Biomass properties vary and are commonly associated with plant species. Hence, efficient methods to predict biofuel characteristics will greatly affect the utilization and management of feedstock production. In this paper attempt was made to correlate various chemical characteristics with NIR spectra. Wood chips from various plant species was analyzed for lignin content, heating value, ash content and NIR and the results were evaluated with correlation, PCA and PCR. Initial evaluation showed promising results where chemical components in the wood correlate to NIR spectra. A selection of results will be presented in this paper. Further analysis as well as results from PCA and PCR models will be presented in the full paper version.
Mathematical and Computer Modelling of Dynamical Systems, 2009
ABSTRACT This paper discusses the accuracy of different types of models. Statistical models are b... more ABSTRACT This paper discusses the accuracy of different types of models. Statistical models are based on process data and/or observations from lab measurements. This class of models are called black box models. Physical models use physical relationships to describe a process. These are called white box models or first principle models. The third group is sometimes called grey box models, being a combination of black box and white box models. Here we discuss two examples of model types. One is a statistical model where an artificial neural network is used to predict NOx in the exhaust gases from a boiler at Mälarenergi AB in Västerås, Sweden. The second example is a grey box model of a continuous digester. The digester model includes mass balances, energy balances, chemical reactions and physical geometrical constraints to simulate the real digester. We also propose that a more sophisticated model is not required to increase the accuracy of the predicted measurements.
A dynamic model is presented for a biomass-fired circulating fluidized bed boiler. The model is b... more A dynamic model is presented for a biomass-fired circulating fluidized bed boiler. The model is based on energy and mass balances for the components in the boiler and on a combustion model for the fluidized bed. The main purpose of the model is to simulate how deposits affect the boiler efficiency and performance. The model is verified against the municipal circulating fluidized bed boiler in Västerås, Sweden, which produces 157 MW. The distribution of deposits on the surfaces in the boiler is well known from inspections. These observations are used as inputs to the model to simulate their effects on boiler performance.
ABSTRACT Forest biomass is a renewable and sustainable source of energy that can be used for prod... more ABSTRACT Forest biomass is a renewable and sustainable source of energy that can be used for producing electricity, heat, and biofuels. The production of biomass for energy is considered to be an important step in developing sustainable communities and managing greenhouse gas emissions effectively. Biomass properties vary and are commonly associated with plant species. Hence, efficient methods to predict biofuel characteristics will greatly affect the utilization and management of feedstock production. In this paper attempt was made to correlate various chemical characteristics with NIR spectra. Wood chips from various plant species was analyzed for lignin content, heating value, ash content and NIR and the results were evaluated with correlation, PCA and PCR. Initial evaluation showed promising results where chemical components in the wood correlate to NIR spectra. A selection of results will be presented in this paper. Further analysis as well as results from PCA and PCR models will be presented in the full paper version.
This paper presents experimental data concerning combustion characteristics of full-scale biomass... more This paper presents experimental data concerning combustion characteristics of full-scale biomass-fired bubbling fluidized bed (BFB) steam boiler with a thermal output of 31 MW. The purpose of the experimental measurements is to show how the values of selected combustion parameters vary in reality depending on measurement position. Experimentation involves specifically a determination of combustion gas temperature and concentration of gas species i.e. O 2 , CO 2 , CO and NO X at different positions in the furnace and the flue gas trains. Character of results from the furnace indicates the intermediate stage of thermochemical reactions. Increased levels of CO close to the wall have been found, this may be indicating reducing atmosphere and thereby increased corrosion risk. Results from flue gas trains demonstrate that behavior there is related to the fluid dynamics and heat transfer, the temperature is too low for further combustion reactions. Results show great variations among measured values of all measurands depending on a distance along the line from the wall to the center of the boiler. The measurements from permanently installed fixed sensors are not giving value representing average conditions, but overall profiles can be correlated to online measurements from fixed sensors.
6th IFAC Symposium on Power Plants and Power Systems Control (2009), 2009
ABSTRACT This paper covers a method for operator decision support, where physical simulation mode... more ABSTRACT This paper covers a method for operator decision support, where physical simulation models are used to connect different physical variables to each other. By comparing energy and material balances for a larger process area inconsistencies in single process parts and sensor measurements can be detected, by following the development between single measurements and values predicted from the simulations. This information then can be used as input to e.g. a BN, Bayesian Network, for decision support. The application has been for a CFB boiler at Mälarenergi AB. The simulators have been made in Modelica respectively a more advanced model in APROS.
This paper presents experimental data concerning combustion characteristics of full-scale biomass... more This paper presents experimental data concerning combustion characteristics of full-scale biomass-fired bubbling fluidized bed (BFB) steam boiler with a thermal output of 31 MW. The purpose of the experimental measurements is to show how the values of selected combustion parameters vary in reality depending on measurement position. Experimentation involves specifically a determination of combustion gas temperature and concentration of gas species i.e. O 2 , CO 2 , CO and NO X at different positions in the furnace and the flue gas trains. Character of results from the furnace indicates the intermediate stage of thermochemical reactions. Increased levels of CO close to the wall have been found, this may be indicating reducing atmosphere and thereby increased corrosion risk. Results from flue gas trains demonstrate that behavior there is related to the fluid dynamics and heat transfer, the temperature is too low for further combustion reactions. Results show great variations among measured values of all measurands depending on a distance along the line from the wall to the center of the boiler. The measurements from permanently installed fixed sensors are not giving value representing average conditions, but overall profiles can be correlated to online measurements from fixed sensors.
ABSTRACT Forest biomass is a renewable and sustainable source of energy that can be used for prod... more ABSTRACT Forest biomass is a renewable and sustainable source of energy that can be used for producing electricity, heat, and biofuels. The production of biomass for energy is considered to be an important step in developing sustainable communities and managing greenhouse gas emissions effectively. Biomass properties vary and are commonly associated with plant species. Hence, efficient methods to predict biofuel characteristics will greatly affect the utilization and management of feedstock production. In this paper attempt was made to correlate various chemical characteristics with NIR spectra. Wood chips from various plant species was analyzed for lignin content, heating value, ash content and NIR and the results were evaluated with correlation, PCA and PCR. Initial evaluation showed promising results where chemical components in the wood correlate to NIR spectra. A selection of results will be presented in this paper. Further analysis as well as results from PCA and PCR models will be presented in the full paper version.
Mathematical and Computer Modelling of Dynamical Systems, 2009
ABSTRACT This paper discusses the accuracy of different types of models. Statistical models are b... more ABSTRACT This paper discusses the accuracy of different types of models. Statistical models are based on process data and/or observations from lab measurements. This class of models are called black box models. Physical models use physical relationships to describe a process. These are called white box models or first principle models. The third group is sometimes called grey box models, being a combination of black box and white box models. Here we discuss two examples of model types. One is a statistical model where an artificial neural network is used to predict NOx in the exhaust gases from a boiler at Mälarenergi AB in Västerås, Sweden. The second example is a grey box model of a continuous digester. The digester model includes mass balances, energy balances, chemical reactions and physical geometrical constraints to simulate the real digester. We also propose that a more sophisticated model is not required to increase the accuracy of the predicted measurements.
A dynamic model is presented for a biomass-fired circulating fluidized bed boiler. The model is b... more A dynamic model is presented for a biomass-fired circulating fluidized bed boiler. The model is based on energy and mass balances for the components in the boiler and on a combustion model for the fluidized bed. The main purpose of the model is to simulate how deposits affect the boiler efficiency and performance. The model is verified against the municipal circulating fluidized bed boiler in Västerås, Sweden, which produces 157 MW. The distribution of deposits on the surfaces in the boiler is well known from inspections. These observations are used as inputs to the model to simulate their effects on boiler performance.
Uploads
Papers by Anders Avelin