A sample of healthy wind turbines from the same wind farm with identical sizes and designs was in... more A sample of healthy wind turbines from the same wind farm with identical sizes and designs was investigated to determine the average vibrational signatures of the drive train components during normal operation. The units were variable-speed machines with three blades. The rotor was supported by two bearings, and the drive train connected to an intermediate three-stage planetary/helical gearbox. The nominal 2 MW output power was regulated using blade pitch adjustment. Vibrations were measured in exactly the same positions using the same type of sensors over a six-month period covering the entire range of operating conditions. The data set was preliminary validated to remove outliers based on the theoretical power curves. The most relevant frequency peaks in the rotor, gearbox, and generator vibrations were detected and identified based on averaged power spectra. The amplitudes of the peaks induced by a common source of excitation were compared in different measurement positions. A wi...
A series of continuous vibration measurements in 14 upwind wind turbines of the same model and be... more A series of continuous vibration measurements in 14 upwind wind turbines of the same model and belonging to the same wind farm have been conducted. The data were acquired over a period lasting approximately half a year. The tower axial vibration acceleration has been monitored in the frequency band from 0 to 10 Hz with an accelerometer mounted on the gearbox casing between the intermediate and the high-speed shafts. It has been observed that the average frequency spectrum is dominated by the blade passing frequency in all the wind turbines. The evolution of the vibration magnitudes over the entire range of operating conditions is also very similar for all the wind turbines. The root-mean-square (rms) acceleration value has been correlated with the wind speed, and it has been found that a linear fit with a positive slope is a useful model for prediction purposes.
IOP Conference Series: Materials Science and Engineering, 2013
The spectral content of the low frequency vibrations in the band from 0 to 10 Hz measured in full... more The spectral content of the low frequency vibrations in the band from 0 to 10 Hz measured in full scale wind turbines has been statistically analyzed as a function of the whole range of steady operating conditions. Attention has been given to the amplitudes of the vibration peaks and their dependency on rotating speed and power output. Two different wind turbine models of 800 and 2000 kW have been compared. For each model, a sample of units located in the same wind farm and operating during a representative period of time have been considered. A condition monitoring system installed in each wind turbine has been used to register the axial acceleration on the gearbox casing between the intermediate and the high speed shafts. The average frequency spectrum has permitted to identify the vibration signature and the position of the first tower natural frequency in both models. The evolution of the vibration amplitudes at the rotor rotating frequency and its multiples has shown that the tower response is amplified by resonance conditions in one of the models. So, it is concluded that a continuous measurement and control of low frequency vibrations is required to protect the turbines against harmful vibrations of this nature.
Note: Using Smart Source Parsing 9-12 September pp 3 Reference LMH-CONF-2002-005 Record created o... more Note: Using Smart Source Parsing 9-12 September pp 3 Reference LMH-CONF-2002-005 Record created on 2005-11-04, modified on 2017-05-10
A sample of healthy wind turbines from the same wind farm with identical sizes and designs was in... more A sample of healthy wind turbines from the same wind farm with identical sizes and designs was investigated to determine the average vibrational signatures of the drive train components during normal operation. The units were variable-speed machines with three blades. The rotor was supported by two bearings, and the drive train connected to an intermediate three-stage planetary/helical gearbox. The nominal 2 MW output power was regulated using blade pitch adjustment. Vibrations were measured in exactly the same positions using the same type of sensors over a six-month period covering the entire range of operating conditions. The data set was preliminary validated to remove outliers based on the theoretical power curves. The most relevant frequency peaks in the rotor, gearbox, and generator vibrations were detected and identified based on averaged power spectra. The amplitudes of the peaks induced by a common source of excitation were compared in different measurement positions. A wi...
A series of continuous vibration measurements in 14 upwind wind turbines of the same model and be... more A series of continuous vibration measurements in 14 upwind wind turbines of the same model and belonging to the same wind farm have been conducted. The data were acquired over a period lasting approximately half a year. The tower axial vibration acceleration has been monitored in the frequency band from 0 to 10 Hz with an accelerometer mounted on the gearbox casing between the intermediate and the high-speed shafts. It has been observed that the average frequency spectrum is dominated by the blade passing frequency in all the wind turbines. The evolution of the vibration magnitudes over the entire range of operating conditions is also very similar for all the wind turbines. The root-mean-square (rms) acceleration value has been correlated with the wind speed, and it has been found that a linear fit with a positive slope is a useful model for prediction purposes.
IOP Conference Series: Materials Science and Engineering, 2013
The spectral content of the low frequency vibrations in the band from 0 to 10 Hz measured in full... more The spectral content of the low frequency vibrations in the band from 0 to 10 Hz measured in full scale wind turbines has been statistically analyzed as a function of the whole range of steady operating conditions. Attention has been given to the amplitudes of the vibration peaks and their dependency on rotating speed and power output. Two different wind turbine models of 800 and 2000 kW have been compared. For each model, a sample of units located in the same wind farm and operating during a representative period of time have been considered. A condition monitoring system installed in each wind turbine has been used to register the axial acceleration on the gearbox casing between the intermediate and the high speed shafts. The average frequency spectrum has permitted to identify the vibration signature and the position of the first tower natural frequency in both models. The evolution of the vibration amplitudes at the rotor rotating frequency and its multiples has shown that the tower response is amplified by resonance conditions in one of the models. So, it is concluded that a continuous measurement and control of low frequency vibrations is required to protect the turbines against harmful vibrations of this nature.
Note: Using Smart Source Parsing 9-12 September pp 3 Reference LMH-CONF-2002-005 Record created o... more Note: Using Smart Source Parsing 9-12 September pp 3 Reference LMH-CONF-2002-005 Record created on 2005-11-04, modified on 2017-05-10
Uploads
Papers by Toufik Mebarki