The Mars Global Surveyor (MGS) Spacecraft made use of aerobraking to gradually reduce its orbit p... more The Mars Global Surveyor (MGS) Spacecraft made use of aerobraking to gradually reduce its orbit period from a highly elliptical insertion orbit to its final science orbit. Aerobraking produces a high heat load on the solar arrays, which have a large surface area exposed to the airflow and relatively low mass. To accurately model the complex behavior during aerobraking, the thermal analysis needed to be tightly coupled to the spatially varying, time dependent aerodynamic heating. Also, the thermal model itself needed to accurately capture the behavior of the solar array and its response to changing heat load conditions. The correlation of the thermal model to flight data allowed a validation of the modeling process, as well as information on what processes dominate the thermal behavior. Correlation in this case primarily involved detailing the thermal sensor nodes, using as-built mass to modify material property estimates, refining solar cell assembly properties, and adding detail to radiation and heat flux boundary conditions. This paper describes the methods used to develop finite element thermal models of the MGS solar array and the correlation of the thermal model to flight data from the spacecraft drag passes. Correlation was made to data from four flight thermal sensors over three of the early drag passes. Good correlation of the model was achieved, with a maximum difference between the predicted model maximum and the observed flight maximum temperature of less than 5%. Lessons learned in the correlation of this model assisted in validating a similar model and method used for the Mars Odyssey solar array aeroheating analysis, which were used during onorbit operations.
A Planetary Entry Systems Synthesis Tool, with applications to conceptual design and modeling of ... more A Planetary Entry Systems Synthesis Tool, with applications to conceptual design and modeling of entry systems has been developed. This tool is applicable to exploration missions that employ entry, descent and landing or aerocapture. An integrated framework ...
Earth entry system options for human return missions from the Moon and Mars were analyzed and com... more Earth entry system options for human return missions from the Moon and Mars were analyzed and compared to identify trends among the configurations and trajectory options and to facilitate informed decision making at the exploration architecture level. Entry system options included ballistic, lifting capsule, biconic, and lifting body configurations with direct entry and aerocapture trajectories. For each configuration and trajectory option, the thermal environment, deceleration environment, crossrange and downrange performance, and entry corridor were assessed. In addition, the feasibility of a common vehicle for lunar and Mars return was investigated. The results show that a low lift-to-drag ratio (L/D = 0.3) vehicle provides sufficient performance for both lunar and Mars return missions while providing the following benefits: excellent packaging efficiency, low structural and TPS mass fraction, ease of launch vehicle integration, and system elegance and simplicity. Numerous configuration options exist that achieve this L/D.
Aerobraking has become a proven approach for orbital missions at Mars. A launch of a 1000 kg clas... more Aerobraking has become a proven approach for orbital missions at Mars. A launch of a 1000 kg class m rp periapsis altitude, km SA solar array s/c spacecraft T spacecraft temperature,°C V spacecraft velocity, km/s
Thermal analysis of a vehicle designed to return samples from another planet, such as the Earth E... more Thermal analysis of a vehicle designed to return samples from another planet, such as the Earth Entry vehicle for the Mars Sample Return mission, presents several unique challenges. The Earth Entry Vehicle (EEV) must contain Martian material samples after they have been collected and protect them from the high heating rates of entry into the Earth's atmosphere. This requirement necessitates inclusion of detailed thermal analysis early in the design of the vehicle. This paper will describe the challenges and solutions for a preliminary thermal analysis of an Earth Entry Vehicle. The aeroheating on the vehicle during entry would be the main driver for the thermal behavior, and is a complex function of time, spatial position on the vehicle, vehicle temperature, and trajectory parameters. Thus, the thermal analysis must be closely tied to the aeroheating analysis in order to make accurate predictions. Also, the thermal analysis must account for the material response of the ablative thermal...
There are numerous challenges associated with placing a spacecraft in orbit around Mars. Often, t... more There are numerous challenges associated with placing a spacecraft in orbit around Mars. Often, trades must be made such as the mass of the payload and the amount of fuel that can be carried. One technique employed to more efficiently place a spacecraft in orbit while maximizing payload mass (minimizing fuel use) is aerobraking. The Mars Odyssey Spacecraft made use of aerobraking to gradually reduce its orbit period from a highly elliptical insertion orbit to its final science orbit. Aerobraking introduces its own unique challenges, in particular, predicting the thermal response of the spacecraft and its components during each aerobraking drag pass. This paper describes the methods used to perform aerobraking thermal analysis using finite element thermal models of the Mars Odyssey Spacecraft's solar array. To accurately model the complex behavior during aerobraking, the thermal analysis must be tightly coupled to the spatially varying, time dependent aerodynamic heating analysis. Also, to properly represent the temperatures prior to the start of the drag pass, the model must include the orbital solar and planetary heat fluxes. It is critical that the thermal behavior be predicted accurately to maintain the solar array below its structural flight allowable temperature limit. The goal of this paper is to describe a thermal modeling method that was developed for this purpose.
Aerobraking has become a proven approach for orbital missions at Mars. A launch of a 1000 kg clas... more Aerobraking has become a proven approach for orbital missions at Mars. A launch of a 1000 kg class spacecraft on a Delta class booster saves 90% of the post-MOI fuel otherwise required to circularize the orbit. In 1997, Mars Global Surveyor demonstrated the feasibility and Mars 2001 Odyssey completed a nearly trouble free aerobraking phase in January 2002. In 2006,
The Mars Global Surveyor (MGS) Spacecraft made use of aerobraking to gradually reduce its orbit p... more The Mars Global Surveyor (MGS) Spacecraft made use of aerobraking to gradually reduce its orbit period from a highly elliptical insertion orbit to its final science orbit. Aerobraking produces a high heat load on the solar arrays, which have a large surface area exposed to the airflow and relatively low mass. To accurately model the complex behavior during aerobraking, the thermal analysis needed to be tightly coupled to the spatially varying, time dependent aerodynamic heating. Also, the thermal model itself needed to accurately capture the behavior of the solar array and its response to changing heat load conditions. The correlation of the thermal model to flight data allowed a validation of the modeling process, as well as information on what processes dominate the thermal behavior. Correlation in this case primarily involved detailing the thermal sensor nodes, using as-built mass to modify material property estimates, refining solar cell assembly properties, and adding detail to radiation and heat flux boundary conditions. This paper describes the methods used to develop finite element thermal models of the MGS solar array and the correlation of the thermal model to flight data from the spacecraft drag passes. Correlation was made to data from four flight thermal sensors over three of the early drag passes. Good correlation of the model was achieved, with a maximum difference between the predicted model maximum and the observed flight maximum temperature of less than 5%. Lessons learned in the correlation of this model assisted in validating a similar model and method used for the Mars Odyssey solar array aeroheating analysis, which were used during onorbit operations.
The Mars Reconnaissance Orbiter (MRO) launched on August 12, 2005 and began aerobraking at Mars i... more The Mars Reconnaissance Orbiter (MRO) launched on August 12, 2005 and began aerobraking at Mars in March 2006. In order to save propellant, MRO used aerobraking to modify the initial orbit at Mars. The spacecraft passed through the atmosphere briefly on each orbit; during each pass the spacecraft was slowed by atmospheric drag, thus lowering the orbit apoapsis. The largest area on the spacecraft, most affected by aeroheating, was the solar arrays. A thermal analysis of the solar arrays was conducted at NASA Langley Research Center to simulate their performance throughout the entire roughly 6-month period of aerobraking. A companion paper describes the development of this thermal model. This model has been correlated against many sets of flight data. Several maneuvers were performed during the cruise to Mars, such as thruster calibrations, which involve large abrupt changes in the spacecraft orientation relative to the sun. The data obtained from these maneuvers allowed the model to be well-correlated with regard to thermal mass, conductive connections, and solar response well before arrival at the planet. Correlation against flight data for both in-cruise maneuvers and drag passes was performed. Adjustments made to the model included orientation during the drag pass, solar flux, Martian surface temperature, through-array resistance, aeroheating gradient due to angle of attack, and aeroheating accommodation coefficient. Methods of correlation included comparing the model to flight temperatures, slopes, temperature deltas between sensors, and solar and planet direction vectors. Correlation and model accuracy over 400 aeroheating drag passes were determined, with overall model accuracy better than 5°C.
The Mars Global Surveyor (MGS) Spacecraft made use of aerobraking to gradually reduce its orbit p... more The Mars Global Surveyor (MGS) Spacecraft made use of aerobraking to gradually reduce its orbit period from a highly elliptical insertion orbit to its final science orbit. Aerobraking produces a high heat load on the solar arrays, which have a large surface area exposed to the airflow and relatively low mass. To accurately model the complex behavior during aerobraking, the thermal analysis needed to be tightly coupled to the spatially varying, time dependent aerodynamic heating. Also, the thermal model itself needed to accurately capture the behavior of the solar array and its response to changing heat load conditions. The correlation of the thermal model to flight data allowed a validation of the modeling process, as well as information on what processes dominate the thermal behavior. Correlation in this case primarily involved detailing the thermal sensor nodes, using as-built mass to modify material property estimates, refining solar cell assembly properties, and adding detail to radiation and heat flux boundary conditions. This paper describes the methods used to develop finite element thermal models of the MGS solar array and the correlation of the thermal model to flight data from the spacecraft drag passes. Correlation was made to data from four flight thermal sensors over three of the early drag passes. Good correlation of the model was achieved, with a maximum difference between the predicted model maximum and the observed flight maximum temperature of less than 5%. Lessons learned in the correlation of this model assisted in validating a similar model and method used for the Mars Odyssey solar array aeroheating analysis, which were used during onorbit operations.
A Planetary Entry Systems Synthesis Tool, with applications to conceptual design and modeling of ... more A Planetary Entry Systems Synthesis Tool, with applications to conceptual design and modeling of entry systems has been developed. This tool is applicable to exploration missions that employ entry, descent and landing or aerocapture. An integrated framework ...
Earth entry system options for human return missions from the Moon and Mars were analyzed and com... more Earth entry system options for human return missions from the Moon and Mars were analyzed and compared to identify trends among the configurations and trajectory options and to facilitate informed decision making at the exploration architecture level. Entry system options included ballistic, lifting capsule, biconic, and lifting body configurations with direct entry and aerocapture trajectories. For each configuration and trajectory option, the thermal environment, deceleration environment, crossrange and downrange performance, and entry corridor were assessed. In addition, the feasibility of a common vehicle for lunar and Mars return was investigated. The results show that a low lift-to-drag ratio (L/D = 0.3) vehicle provides sufficient performance for both lunar and Mars return missions while providing the following benefits: excellent packaging efficiency, low structural and TPS mass fraction, ease of launch vehicle integration, and system elegance and simplicity. Numerous configuration options exist that achieve this L/D.
Aerobraking has become a proven approach for orbital missions at Mars. A launch of a 1000 kg clas... more Aerobraking has become a proven approach for orbital missions at Mars. A launch of a 1000 kg class m rp periapsis altitude, km SA solar array s/c spacecraft T spacecraft temperature,°C V spacecraft velocity, km/s
Thermal analysis of a vehicle designed to return samples from another planet, such as the Earth E... more Thermal analysis of a vehicle designed to return samples from another planet, such as the Earth Entry vehicle for the Mars Sample Return mission, presents several unique challenges. The Earth Entry Vehicle (EEV) must contain Martian material samples after they have been collected and protect them from the high heating rates of entry into the Earth's atmosphere. This requirement necessitates inclusion of detailed thermal analysis early in the design of the vehicle. This paper will describe the challenges and solutions for a preliminary thermal analysis of an Earth Entry Vehicle. The aeroheating on the vehicle during entry would be the main driver for the thermal behavior, and is a complex function of time, spatial position on the vehicle, vehicle temperature, and trajectory parameters. Thus, the thermal analysis must be closely tied to the aeroheating analysis in order to make accurate predictions. Also, the thermal analysis must account for the material response of the ablative thermal...
There are numerous challenges associated with placing a spacecraft in orbit around Mars. Often, t... more There are numerous challenges associated with placing a spacecraft in orbit around Mars. Often, trades must be made such as the mass of the payload and the amount of fuel that can be carried. One technique employed to more efficiently place a spacecraft in orbit while maximizing payload mass (minimizing fuel use) is aerobraking. The Mars Odyssey Spacecraft made use of aerobraking to gradually reduce its orbit period from a highly elliptical insertion orbit to its final science orbit. Aerobraking introduces its own unique challenges, in particular, predicting the thermal response of the spacecraft and its components during each aerobraking drag pass. This paper describes the methods used to perform aerobraking thermal analysis using finite element thermal models of the Mars Odyssey Spacecraft's solar array. To accurately model the complex behavior during aerobraking, the thermal analysis must be tightly coupled to the spatially varying, time dependent aerodynamic heating analysis. Also, to properly represent the temperatures prior to the start of the drag pass, the model must include the orbital solar and planetary heat fluxes. It is critical that the thermal behavior be predicted accurately to maintain the solar array below its structural flight allowable temperature limit. The goal of this paper is to describe a thermal modeling method that was developed for this purpose.
Aerobraking has become a proven approach for orbital missions at Mars. A launch of a 1000 kg clas... more Aerobraking has become a proven approach for orbital missions at Mars. A launch of a 1000 kg class spacecraft on a Delta class booster saves 90% of the post-MOI fuel otherwise required to circularize the orbit. In 1997, Mars Global Surveyor demonstrated the feasibility and Mars 2001 Odyssey completed a nearly trouble free aerobraking phase in January 2002. In 2006,
The Mars Global Surveyor (MGS) Spacecraft made use of aerobraking to gradually reduce its orbit p... more The Mars Global Surveyor (MGS) Spacecraft made use of aerobraking to gradually reduce its orbit period from a highly elliptical insertion orbit to its final science orbit. Aerobraking produces a high heat load on the solar arrays, which have a large surface area exposed to the airflow and relatively low mass. To accurately model the complex behavior during aerobraking, the thermal analysis needed to be tightly coupled to the spatially varying, time dependent aerodynamic heating. Also, the thermal model itself needed to accurately capture the behavior of the solar array and its response to changing heat load conditions. The correlation of the thermal model to flight data allowed a validation of the modeling process, as well as information on what processes dominate the thermal behavior. Correlation in this case primarily involved detailing the thermal sensor nodes, using as-built mass to modify material property estimates, refining solar cell assembly properties, and adding detail to radiation and heat flux boundary conditions. This paper describes the methods used to develop finite element thermal models of the MGS solar array and the correlation of the thermal model to flight data from the spacecraft drag passes. Correlation was made to data from four flight thermal sensors over three of the early drag passes. Good correlation of the model was achieved, with a maximum difference between the predicted model maximum and the observed flight maximum temperature of less than 5%. Lessons learned in the correlation of this model assisted in validating a similar model and method used for the Mars Odyssey solar array aeroheating analysis, which were used during onorbit operations.
The Mars Reconnaissance Orbiter (MRO) launched on August 12, 2005 and began aerobraking at Mars i... more The Mars Reconnaissance Orbiter (MRO) launched on August 12, 2005 and began aerobraking at Mars in March 2006. In order to save propellant, MRO used aerobraking to modify the initial orbit at Mars. The spacecraft passed through the atmosphere briefly on each orbit; during each pass the spacecraft was slowed by atmospheric drag, thus lowering the orbit apoapsis. The largest area on the spacecraft, most affected by aeroheating, was the solar arrays. A thermal analysis of the solar arrays was conducted at NASA Langley Research Center to simulate their performance throughout the entire roughly 6-month period of aerobraking. A companion paper describes the development of this thermal model. This model has been correlated against many sets of flight data. Several maneuvers were performed during the cruise to Mars, such as thruster calibrations, which involve large abrupt changes in the spacecraft orientation relative to the sun. The data obtained from these maneuvers allowed the model to be well-correlated with regard to thermal mass, conductive connections, and solar response well before arrival at the planet. Correlation against flight data for both in-cruise maneuvers and drag passes was performed. Adjustments made to the model included orientation during the drag pass, solar flux, Martian surface temperature, through-array resistance, aeroheating gradient due to angle of attack, and aeroheating accommodation coefficient. Methods of correlation included comparing the model to flight temperatures, slopes, temperature deltas between sensors, and solar and planet direction vectors. Correlation and model accuracy over 400 aeroheating drag passes were determined, with overall model accuracy better than 5°C.
Uploads
Papers by John Dec