Skip to main content

Questions tagged [induction-heater]

Filter by
Sorted by
Tagged with
4 votes
2 answers
476 views

Understanding the discrepancy between Input and Output power in ZVS Induction heater

I am using a ZVS induction heater like this: Image Source The schematic looks akin to this (schematic has not been tested) Schematic Source I modified it with IRF3205 N-Channel MOSFETs for better ...
15 Volts's user avatar
  • 719
3 votes
1 answer
120 views

How to digitally detect resonance in induction heater circuit?

System description: H-bridge network of IGBTs (inverter) is used to supply power to a parallel LC circuit connected through matching inductor. It is desired to drive the parallel LC circuit in ...
AR2020's user avatar
  • 82
6 votes
3 answers
717 views

Why does a power inductor make a loud noise when first turned on then decay to a calmer "hum" later?

I'm puzzled by this phenomenon. According to my lacking knowledge, a huge current draw at startup is exclusive to electric motors, where the lack of back EMF at zero speed causes big current draw. So ...
Ömer Gezer's user avatar
0 votes
1 answer
147 views

Building a half-bridge zero-voltage switching inverter for induction heating

I am not an electrical professional so please me patient with me. I'm trying to build a half-bridge ZVS inverter for a small induction heater (I want to try to do some small scale welding). I tried my ...
Brick's user avatar
  • 1
1 vote
0 answers
97 views

Induction Cooking Power Stage and EMI Filter Schematic

Recently I am planning to build an induction cooktop using half-bridge resonant topology. For a start, I took a look into ST evaluation board for induction cooking and wondering some part. Here is the ...
HiPeng's user avatar
  • 19
0 votes
2 answers
227 views

LC Parallel resonance induction heater

Consider parallel LC resonance induction circuit with solid iron workpiece, inserted in the inductor. Is it possible to obtain more heat power output from the heated solid iron workpiece in the ...
Fan's user avatar
  • 39
0 votes
0 answers
231 views

Why does one MOSFET heat up very fast compared to the other MOSFET in this induction heater circuit?

simulate this circuit – Schematic created using CircuitLab I'll start off by saying this project is just an experiment I'm playing around with and is not the typical ZVS design you find ...
DanZ's user avatar
  • 131
1 vote
2 answers
295 views

Low voltage induction heating working

I have a question regarding the working of induction heater when powered with low DC voltage source. I have seen some with 12-48V DC in eCommerces like AliExpress. I have knowledge on how induction ...
Burton's user avatar
  • 15
3 votes
2 answers
288 views

Why doesn't an induction heater and an induction ring launcher produce the same effect?

I want to know why an induction heater and an induction ring launcher don't produce the same effect. Both seem to use AC voltage to power a solenoid(which induces a voltage in a pipe) so why doesn't ...
Yassin's user avatar
  • 43
0 votes
1 answer
183 views

Induction cooktop tripping breaker (the IGBT was just repaced) [closed]

I have replaced the burned IGBT + added a new thermal paste, and it worked fine for about 10 minutes on the lower power setting, but when I turned it up to max it failed after a few seconds. I haven't ...
Tomáš Pilný's user avatar
14 votes
4 answers
4k views

According to my understanding, this induction heater should be melted, but it's not. Why not?

I opened up this induction heater to find that it only has maybe 12 AWG wire in its work coil, rated for 30 A RMS. I've been doing induction heater simulations for a project, and the two topologies I'...
Popeye's user avatar
  • 417
1 vote
0 answers
148 views

How to model the workcoil and workpiece in an induction heater?

I'm trying to simulate an induction heater, and I'd first like to start with the load. Sorry if this is a little wordy... I understand the coil and workpiece are treated as a transformer, where the ...
Popeye's user avatar
  • 417
0 votes
0 answers
271 views

ZVS induction heater gets really hot diodes

I'm an embedded software developer and am trying to up my electronics and board design knowledge. As a good first exercise I made a ZVS induction heater. project link Once assembled I was happy to see ...
Geoxion's user avatar
  • 394