AWESOME WATER COOLER IS TRIPPING THE POWER

Water Coolers Refillable OR Bottless What Water are You Drinking? Tap? Filled With Chlorine & Fluoride. OR Bottled Water?​Not Sure If The Plastic Is BPA FREE?. How much money are you spending on water? Water Shouldn't Cost The Earth Filter You Tap Water ​$0.65 Per Liter A.W Filters Removes 98% Chlorine Optional 2 OR 5 Micron OR Fluoride Eliminators 97% Alkaline Water Sticks (Ph 9.5.) Magnesium Prill Beads (Ph 8.0) Miafan Stones https://www.watercoolerswa.com/store/c1/Featured_Products.html
8 Pins
·
3y
WATER COOLER IS TRIPPING THE POWER
3. Kettle – Hot Pot Burnt Out IF motherboard is OK, then it is most likely the kettle – hot pot has burn out. The kettle – Hot pot needs replacing. 4. Fuse needs replacing Located via back of machine Open the fusing casing with flat nose screwdriver pushing in & turning anti-clockwise Check if fuse is damaged Replace with 10A –250v Fuse IF no fuse casing via back of water cooler < 2006 model
WATER COOLER IS TRIPPING THE POWER
Leave wires stay intact. Undo metal box Remove 2 x screws via back of water coolers IF no box < 2006 model (rare parts) Check for damage ( burnt out) on the motherboard. If none via front, undo the motherboard from the casing and check back of motherboard It is possible hot got damaged, but cold is still working. Check for signs of damage, if so needs to be replaced.
WATER COOLER IS TRIPPING THE POWER
IF the power trips when turning on the hot, it could be either the hot relay button located on the motherboard that is damaged, OR Kettle – hot pot element that has burned out. 2. Check motherboard for damage Turn off water cooler power & unplug Unscrew 2 x screws at back Remove lid wiggle off to loosen Remove Lid
WATER COOLER IS TRIPPING THE POWER
If the power trips when turning on either the motherboard needs replacing OR The compressor has died. Check to make sure water is coming from the HOT TAP. IF NOT wait another 10 minutes once water is running freely you can turn on the HOT side, by pushing the RED Heat button top left. They should be a red triangle grid with red flames Wait 5 minutes for the hot water to start heating
WATER COOLER IS TRIPPING THE POWER
Leave turned off till water has filtered through. No lights should be on the digital screen (RED OR BLUE) Check to make sure water can be dispenser from hot tap before turning ON Turn cold water on first, by pushing the BLUE Cool button only once. The blue snowflake & blue triangle grid will come on. Wait about 3 minutes to see if compressor kicks in, listen for a fridge like noise
WATER COOLER IS TRIPPING THE POWER
Electronics got wet due to tank overflowing Empty tank via taps, till emptied Unscrew float valve (upside down cup) bottom of bottle set (older beige in colour) (new BPA FREE white in colour) Empty water cooler of all its water All a day to dry all electrical components Clean all bottle set parts thoroughly Make sure float value is secular tightened Add all washers to their correct positions. Assemble water cooler
WATER COOLER IS TRIPPING THE POWER
Causes: 1. The water tank has overflown (electronics got wet) 2. Motherboard is damaged 3. Kettle – Hot Pot has burned out 4. Fuse needs replacing Remove bottle set of water cooler. Check level of water inside tank. Should look 2 – 3 inches down IF higher float valve not working (Pull apart and clean or replace
WATER COOLER IS TRIPPING THE POWER
Causes: 1. The water tank has overflown (electronics got wet) 2. Motherboard is damaged 3. Kettle – Hot Pot has burned out 4. Fuse needs replacing Remove bottle set of water cooler. Check level of water inside tank. Should look 2 – 3 inches down IF higher float valve not working (Pull apart and clean or replace